Makita EW320TR Owner's Manual download pdf (Page 27)

1. STARTING (See Fig.

(1) Open the fuel cock. (See Fig.3

q) (Except EW120R)

(2) Set the throttle lever to the idling position (L).

(See Fig.3-w) (EW120R)

Set the speed control lever 1/3 of the way towards the

high speed position. (See Fig.3-e) (Except EW120R)

(3) Set the stop switch to the position “

” (ON).

(See Fig.3

r,t)

(4) Close the choke lever. (See Fig.3

y,u)

■

If the engine is cold or the ambient temperature is low,

close the choke lever fully.

■

If the engine is warm or the ambient temperature is high,

open the choke lever half-way, or keep it fully open.

(5) Push the primer pump 7 to 10 times to feed the fuel to

the carburetor. (See Fig.3

(6) Pull the starter handle slowly until resistance is felt. This

is the “compression” point. Return the handle to its

original position and pull swiftly. Do not pull out the rope

all the way. After starting the engine, allow the starter

handle to return to its original position while still holding

the handle. (See Fig.3

o,!0)

(7) After starting the engine, gradually open choke by turning

the choke lever and finally keep it fully opened. Do not

fully open the choke lever immediately when the engine

is cold or the ambient temperature is low, because the

engine may stop. (See Fig.3

!1,!2)

4. OPERATING YOUR PUMP

2. RUNNING (See Fig.

(1) After the engine starts, set the speed control lever at the

low speed position (L) and warm it up without load for a

few minutes.

(See Fig.4

q,w)

(2) Gradually move the speed control lever toward the high

speed position (H) and set it at the required engine speed.

(See Fig.4

e,r)

■

Whenever high speed operation is not required, slow the

engine down (idle) by moving the speed control lever to

save fuel and extend engine life.

3. STOPPING (See Fig.

(1) Speed control lever

■

Set the speed control lever at the low speed position and

allow the engine to run at low speed for 2 or 3 minutes

before stopping. (See Fig.5

q) (EW120R)

■

Set the speed control lever at the low speed position and

allow the engine to run at low speed for 1 or 2 minutes

before stopping. (See Fig.5

w) (Except EW120R)

(2) Set the stop switch to the position “

” (OFF).

(See Fig.5-e,r)

■

Do not stop the engine suddenly when it is running at

high speed.

(3) Close the fuel cock. (See Fig.5

t) (Except EW120R)

(4) Pull the starter handle slowly and return the handle to its

original position when resistance is felt. This operation is

necessary to prevent outside moist air from intruding

into the combustion chamber. (See Fig.5

※※

※ STOPPING ENGINE WITH THE FUEL COCK

(Except EW120R)

Close the fuel cock and wait for a while until the engine stops.

Avoid to let the fuel remain in the carburator over long periods,

or the passages of the carburator may become clogged with

impurities, and malfunctions may result.

5. MAINTENANCE

(See Fig.

)

1. DAILY INSPECTION

Before running the engine, check the following service items.

q Loose or broken bolts and nuts

w Clean air cleaner element

e Enough clean engine oil

r Leakage of gasoline and engine oil

t Enough gasoline

y Safe surroundings

u Check the priming water

i Excessive vibration, noise

NOTE

If the engine is operated at upside down, white smoke may

be exhausted from the muffler. (EW120R)

1 2 ... 22 23 24 25 26 27 28 29 30 31 32 ... 151 152

Makita EW320TR Owner's Manual Page 27

Comments to this Manuals

Makita EW320TR Owner's Manual Page 27

Comments to this Manuals

Related products and manuals for Lawnmowers Makita EW320TR