Makita DPC7001 Owner's Manual download pdf (Page 14)

Fit the pressure disc (M/16) on the shaft, observing the

flattened side of the shaft.

NOTE:

The arbor hole of the pressure disc is shaped to fit the

shaft. When putting the pressurediscon the shaft, turn itslightly

until it fits.

Screw in the Allen screw (M/15) by turning it to the left

(counter-clockwise

left-hand thread!) and tighten by hand.

Slowly turn the cutting disc until the stop hole of the V-belt

wheel is visible in the drive-arm hole (M/18).

Push the assembly tool (M/19)

all

the way into the stop hole

of the V-belt wheel. The shaft is now blocked.

Tighten the Allen screw with the Allen key (M/20).

NOTE:

Tighten the Allen screw tightly. If this is not done, the

cutting disc can slip during cutting.

Fuels/

Refuelling

Gasoline

50:l

Us-gal. (3.7

2.5 Us-gal. (9.4

5.0 Us-gaL(18.9

2.5

floz.

(75 cm3)

6.4

floz.

(189 cm3)

12.8 floz. (378 cm3)

25:l

other

oil

5.0

floz.

(150 cm3)

2.8

floz.

(378 cm3)

5.6 floz. (756 cm3)

Fuel mixture

The Power Cut is powered by a high-performance two-stroke

engine. It runs on a mixture of gasoline and two-stroke engine

oil.

The engine is designed for unleaded regular gasoline with amin.

octane value of 91

ROZ.

In case no such fuel is available, you

can use fuel with a higher octane value. This will not affect the

engine.

In order to obtain an optimum engine output and to protect

your health and the environment use unleaded fuel only.

Gasoline which contens alcohol should not used in MAKITA

products.

For lubricating the engine use a two-stroke engine oil (quality

grade:

TC-3),

which is added to the fuel. The engine has been

designed for use of MAKITA high-performance two-stroke en-

gine oil and a mixture ratio of only 50:l to protect the environ-

ment. In addition, a long service life and reliable operation with

a minimum emission of exhaust gases are ensured.

MAKITA high-performance two-stroke engine oil is available in

the following sizes to suit your individual requirements:

The correct mixture ratio:

50:l

251

when using MAKITA high-performance two-stroke engi-

ne oil, i. e. mix 50 parts gasoline with 1 part oil.

when usingothertwo-strokeengineoils, i. e. mix25parts

gasoline with 1 part oil.

NOTE:

For preparing the fuel-oil mixture first mix the entire oil quantity

with half of the fuel required, then add the remaining fuel.

Thoroughly shake the mixture before filling it into the Power Cut

tank.

It is not wise to add more engine oil than specified to ensure safe

operation. This will only result in a higher production of combus-

tion residues which will pollute the environment and clog the

exhaust channel in the cylinder as well as the muffler. In

addition, fuel consumption will rise and performance will de-

crease.

Fuel storage

Fuels

haveonlyalimitedshelf-life.

Buyonlyas muchasyou will

use in

weeks.

Store fuel only in approved and marked containers.

AVOID SKIN AND

EYE

CONTACT

order number 980

008

607

order number 980

008

606

100 ml

case MAKITA high-performance two-stroke engine oil is not

available, it

urgently recommended to use a mixture ratio of

25:1, as otherwise optimum operation of the engine cannot be

guaranteed.

Mineral oil products degrease your skin. If your skin comes in

contact with these substances repeatedly and for an extended

period of time, it will desiccate. Various skin deseases may

result. In addition, allergic reactions are known to occur.

Eyes can be irritated by contact with oil. If oil comes into your

eyes, immediately wash them with clear water.

If your eyes are still irritated, see a doctor immediately!

1 2 ... 9 10 11 12 13 14 15 16 17 18 19 ... 51 52

Comments to this Manuals

No comments

Makita DPC7001 Owner's Manual Page 14

Comments to this Manuals