Makita LS1016 Instruction Manual Page 6
- Page / 76
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
6
unplug the tool may result in serious personal injury
from accidental start-up.
Blade guard
1
009485
When lowering the handle, the blade guard rises
automatically. The blade guard returns to its original
position when the cut is completed and the handle is
raised.
WARNING:
• Never defeat or remove the blade guard or the
spring which attaches to the guard. An exposed
blade as a result of defeated guarding may result in
serious personal injury during operation.
In the interest of your personal safety, always maintain
the blade guard in good condition. Any irregular
operation of the blade guard should be corrected
immediately. Check to assure spring loaded return action
of guard.
WARNING:
• Never use the tool if the blade guard or spring
are damaged, faulty or removed. Operation of
the tool with a damaged, faulty or removed guard
may result in serious personal injury.
If the see-through blade guard becomes dirty, or sawdust
adheres to it in such a way that the blade and/or
workpiece is no longer easily visible, unplug the saw and
clean the guard carefully with a damp cloth. Do not use
solvents or any petroleum-based cleaners on the plastic
guard because this may cause damage to the guard.
If the blade guard becomes dirty and needs to be
cleaned for proper operation follow the steps below:
With the tool switched off and unplugged, use the
supplied socket wrench to loosen the hex bolt holding the
center cover. Loosen the hex bolt by turning it
counterclockwise and raise the blade guard and center
cover. With the blade guard so positioned, cleaning can
be more completely and efficiently accomplished. When
cleaning is complete reverse procedure above and
secure bolt. Do not remove spring holding blade guard. If
guard becomes damaged through age or UV light
exposure, contact a Makita service center for a new
guard. DO NOT DEFEAT OR REMOVE GUARD.
1
009486
Positioning kerf board
1
009488
1
2
3
4
5
6
001538
This tool is provided with the kerf boards in the turn base
to minimize tearing on the exit side of a cut. The kerf
boards are factory adjusted so that the saw blade does
not contact the kerf boards. Before use, adjust the kerf
boards as follows:
1
2
009496
1. Lock lever
2. Locking screw
1. Saw blade
2. Blade teeth
3. Kerf board
4. Left bevel cut
5. Straight cut
6. Right bevel cut
1. Kerf board
1. Blade guard
1. Blade guard
- Slide Compound Miter Saw 1
- Scie à Onglet Radiale 1
- USA007-2 2
- ADDITIONAL SAFETY RULES 4
- SAVE THESE INSTRUCTIONS 5
- FOR THE LASER 5
- INSTALLATION 5
- FUNCTIONAL DESCRIPTION 5
- Blade guard 6
- Positioning kerf board 6
- Stopper arm 7
- Adjusting the miter angle 8
- Adjusting the bevel angle 8
- Slide lock adjustment 8
- ASSEMBLY 10
- Dust bag 11
- Securing workpiece 12
- Vertical vise 13
- OPERATION 14
- Miter angle Bevel angle 15
- Left and Right 0 - 45 15
- Table (B) 16
- Compound Miter Saw 18
- Table (C) 20
- MAINTENANCE 21
- ACCESSORIES 24
- RÈGLES DE SÉCURITÉ 28
- SUPPLÉMENTAIRES 28
- CONSERVEZ CE MODE 29
- D'EMPLOI 29
- ADDITIONNELLES POUR LE 29
- DESCRIPTION DU 30
- FONCTIONNEMENT 30
- Bras de blocage 32
- Interrupteur 33
- Frein électrique 34
- Fonction électronique 34
- Action du faisceau laser 34
- ASSEMBLAGE 35
- Sac à poussières 36
- Immobilisation de la pièce 37
- Étau vertical 38
- UTILISATION 39
- Gauche et droite 0 à 45 41
- Tableau (B) 42
- EN0002-1 43
- EN0003-1 44
- Tableau (C) 45
- ENTRETIEN 46
- Remplacement des charbons 49
- Après l'utilisation 49
- ACCESSOIRES 50
- NORMAS DE SEGURIDAD 53
- ADICIONALES 53
- Advertencias y precauciones 53
- GUARDE ESTAS 54
- INSTRUCCIONES 54
- ADICIONALES PARA EL LÁSER 54
- INSTALACIÓN 55
- DESCRIPCIÓN DEL 55
- FUNCIONAMIENTO 55
- Brazo de retención 57
- Ajuste del ángulo inglete 57
- Ajuste del ángulo bisel 58
- Freno eléctrico 59
- Función electrónica 59
- Función de inicio suave 59
- Accionamiento del rayo láser 59
- ENSAMBLE 60
- Bolsa recolectora de polvo 61
- Prensa vertical 63
- OPERACIÓN 64
- Izquierda y Derecha 0 – 45 66
- Tabla (B) 67
- Sierra de Inglete 68
- Tabla (C) 70
- MANTENIMIENTO 71
- Luego del uso 74
- ACCESORIOS 75
- ADVERTENCIA 76
Related products and manuals for Circular saws Makita LS1016
Circular saws Makita JV0600 User Manual
(48 pages)
(48 pages)
Circular saws Makita JR3050T Specifications
(16 pages)
(16 pages)
Circular saws Makita LS0714L Instruction Manual
(136 pages)
(136 pages)
Circular saws Makita DPC6440 Owner's Manual
(68 pages)
(68 pages)
Circular saws Makita 51778 User Manual
(52 pages)
(52 pages)
Circular saws Makita VTP-16A User Manual
(27 pages)
(27 pages)
(72 pages)
(36 pages)
Circular saws Makita MLT100 User Manual
(72 pages)
(72 pages)
Circular saws Makita 5277B Specifications
(20 pages)
(20 pages)
Circular saws Makita 5007FA Specifications
(20 pages)
(20 pages)
© 2020, manymanuals.com. All rights reserved. | 0.907 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals