Makita EBH252U Instruction Manual

EBH252UEBH253UEBH252LEBH253LPetrol BrushcutterEBH252UEBH253UEBH252LEBH253LORIGINAL INSTRUCTION MANUALImportant:Read this instruction manual carefully

10CAUTION: Before doing any work on the Petrol Brushcutter, always stop the engine and pull the spark plug connector off the spark plug. Always wear

11To meet the applicable safety provisions, only the tool/ protector combinations as indicated in the table must be used.Be sure to use genuine MAKIT

12Turn the machine upside down, and you can replace the cutter blade or nylon cutting head easily.– Insert the hex wrench through the hole in the gea

13Inspection and rell of engine oil– Perform the following procedure, with the engine cooled down.– While keeping the engine level, remove the oil

14REFUELINGHandling of fuelIt is necessary to handle fuel with utmost care. Fuel may contain substances similar to solvents. Refueling must be perform

15Attachment of shoulder strap– Adjust the strap length so that the cutter blade will be kept parallel with the ground.For EBH252U, EBH253UNOTE: Be

162) Set the I-O switch (1) to OPERATION.3) Choke lever Close the choke lever. Choke opening: – Full closing in cold or when the engine is cold.

17B: Startup after warm-up operation1) Push the primer pump repeatedly. 2) Keep the throttle lever at the idling position. 3) Pull the recoil st

18NYLON CUTTING HEADThe nylon cutting head is a dual string trimmer head capable of both automatic and bump & feed mechanisms.The nylon cutting he

19REPLACEMENT OF ENGINE OIL Deteriorated engine oil will shorten the life of the sliding and rotating parts to a great extent. Be sure to check the pe

2Thank you very much for purchasing the MAKITA Petrol Brushcutter. We are pleased to recommend to you the MAKITA Petrol Brushcutter which is the resul

20CLEANING OF AIR CLEANERDANGER: INFLAMMABLES STRICTLY PROHIBITEDInterval of Cleaning and Inspection: Daily (every 10 operating hours)– Turn the chok

21CLEANING OF FUEL FILTERWARNING: INFLAMMABLES STRICTLY PROHIBITEDInterval of Cleaning and Inspection: Monthly (every 50 operating hours)Suction head

22WARNING: When draining the fuel, be sure to stop the engine and conrm that the engine cools down. Just after stopping the engine, it may still hot

23*1 Perform initial replacement after 20h operation.*2 For the 200 operating hour inspection, request Authorized Service Agent or a machine shop.

24TROUBLESHOOTINGBefore making a request for repairs, check a trouble for yourself. If any abnormality is found, control your machine according to the

Makita CorporationAnjo, Aichi, Japan884909C228

3General Instructions– To ensure correct operation, user has to read this instruction manual to make himself familiar with the handling of the Petrol

4Start the Petrol Brushcutter only in accordance with the instructions.– Do not use any other methods for starting the engine!– Use the Petrol Brush

5Method of operation– Only use the Petrol Brushcutter in good light and visibility. During the winter season beware of slippery or wet areas, ice and

6EC-DECLARATION OF CONFORMITYPetrol Brushcutter: model EBH252U, EBH253U, EBH252L, EBH253L (See TECHNICAL DATA for the specications)We declare under

7TECHNICAL DATA EBH252U, EBH252LModelEBH252U EBH252LBike handle Loop handleDimensions: length x width x height (without cutting blade) mm1,770 x 620

8TECHNICAL DATA EBH253U, EBH253LModelEBH253U EBH253LBike handle Loop handleDimensions: length x width x height (without cutting blade) mm1,770 x 620

9⑱④⑤⑦⑧⑨⑪⑩⑫⑬⑭⑮④⑤⑰⑦⑨⑪⑩⑫⑭⑯EBH252LEBH253LEBH252UEBH253U①③⑥⑲②2221DESIGNATION OF PARTSGB DESIGNATION OF PARTS1 Fuel tank2 Rewind starter3 Air cleaner4 I-O s