Makita AN944 Instruction Manual download pdf (Page 2)

ENGLISH

TECHNICAL DATA

Model number AN944

Type of tool ...................................................................................28 Degree Framing Nailer

Dimension

....................................................................................17-1/2” x 4-31/32” x 13-11/32”

(445 mm x 126 mm x 339 mm

)

Weight of tool ...............................................................................6.97 lbs (3.16 Kg)

Compressed air

Maximum permissible operating pressure ................................ 120 PSIG

Recommended operating pressure .......................................... 70 – 120 PSIG (4.9 – 8.3 bar)

Air consumption per driving operation.......................................2.159 litres/cycle (0.076 scf/cycle) at 101 PSIG

(7 bar) operating pressure

Noise characteristic values in accordance with

Maximum A-weighted impulse sound power level..................... 104.8 dBA

Maximum A-weighted surface impulse sound pressure level .......94.8 dBA

Recommended lubrications

Fastener specifications ................................................................. 0.113” – 0.131” (2.8 – 3.3 mm)

length 2” – 3-1/2” (50 – 90 mm)

Accessories ..................................................................................Wrench 3, 4, 5, 6

Applications & suitability............................................................... Framing, Decking, Trusses, Siding, Subfloor,

Fencing, Sheathing, Pallets and Crate Assembly

Actuating system (Vsafety yoke installed) ...................................Contact/Single sequential actuation

Trigger device ...............................................................................Finger pressure activation

Filling the magazine

1. Slide up to 3 strips of nail into the magazine until they pass through the nail stop lever.

2. Pull back the pusher until it is behind the loaded nail.

3. Release the pusher to engage the nail strips, remembering to keep finger clear.

IMPORTANT SAFETY INSTRUCTIONS

WARNING: WHEN USING THIS TOOL, BASIC

SAFETY PRECAUTIONS SHOULD ALWAYS BE FOL-

LOWED TO REDUCE THE RISK OF PERSONAL

INJURY, INCLUDING THE FOLLOWING:

READ ALL INSTRUCTIONS.

1. For personal safety and proper operation and

maintenance of the tool, read this instruction

manual carefully before using the tool.

2. Always wear safety glasses to protect your eyes

from dust or nail injury. The safety glasses

should conform with the requirements of ANSI

Z87.1.

WARNING:

It is an employer’s responsibility to enforce the

use of safety eye protection equipment by the

tool operators and by other persons in the imme-

diate working area.

3. Wear hearing protection to protect your ears

against exhaust noise and head protection. Also

wear light but not loose clothing. Sleeves should

be buttoned or rolled up. No necktie should be

worn.

4. Rushing the job or forcing the tool is dangerous.

Handle the tool carefully. Do not operate when

under the influence of alcohol, drugs or the like.

5. General Tool Handling Guidelines:

(1) Always assume that the tool contains fasten-

ers.

(2) Do not point the tool toward yourself or any-

one whether it contains fasteners or not.

(3) Do not actuate the tool unless the tool is

placed firmly against the workpiece.

(4) Respect the tool as a working implement.

(5) No horseplay.

(6) Do not hold or carry the tool with a finger on

the trigger.

(7) Do not load the tool with fasteners when any

one of the operating controls is activated.

(8) Do not operate the tool with any power

source other than that specified in the tool

operating/safety instructions.

6. An improperly functioning tool must not be

used.

7. Sparks sometimes fly when the tool is used. Do

not use the tool near volatile, flammable materi-

als such as gasoline, thinner, paint, gas, adhe-

sives, etc.; they will ignite and explode, causing

serious injury.

8. The area should be sufficiently illuminated to

assure safe operations. The area should be clear

and litter-free. Be especially careful to maintain

good footing and balance.

9. Only those involved in the work should be in the

vicinity. Children especially must be kept away at

all times.

10. There may be local regulations concerning noise

which must be complied with by keeping noise

levels within prescribed limits. In certain cases,

shutters should be used to contain noise.

11. Do not play with the contact element: it prevents

accidental discharge, so it must be kept on and

not removed. Securing the trigger in the ON

position is also very dangerous. Never attempt

to fasten the trigger. Do not operate a tool if any

portion of the tool operating controls is inopera-

ble, disconnected, altered, or not working prop-

erly.

1 2 3 4 5 6 7 ... 11 12

Comments to this Manuals

No comments

Makita AN944 Instruction Manual Page 2

Comments to this Manuals

Related products and manuals for Nail Gun Makita AN944