Makita LF1000 User Manual Page 1

Model No. DescriptionNEW TOOLCONCEPT AND MAIN APPLICATIONS SpecificationP 1 / 30 Flip Over Saw 260mm (10-1/4")Model LF1000 is the first flip over

P 10/ 30 Repair[3] DISASSEMBLY/ASSEMBLYFig. 23Fig. 24 Fig. 25ASSEMBLING[3] -5. Blade Case Section (cont.)Slide Sleeve 13 as far as possible toward Ste

P 11/ 30 Repair[3] DISASSEMBLY/ASSEMBLY[3] -6. Riving KnifeFig. 27Fig. 26DISASSEMBLING1) Loosen Wing nut M8.1) First, fix riving knife as illustrated

P 12/ 30Repair[3] DISASSEMBLY/ASSEMBLY[3] -7. Table SectionFig. 29 Fig. 30Fig. 28DISASSEMBLINGPan head screw M4x10Pan head screwM4x10Thrust needle gau

P 13/ 30 Repair[3] DISASSEMBLY/ASSEMBLYDISASSEMBLING[3] -7. Table Section (cont.)Fig. 33Fig. 346) Now the Table section can be removed from Guide fenc

P 14/ 30 Repair[3] DISASSEMBLY/ASSEMBLYDISASSEMBLING[3] -7. Table Section (cont.)Fig. 359) Lever (Lock lever) is fastened to Frame with each two piece

P 15/ 30 Repair[3] DISASSEMBLY/ASSEMBLY[3] -8. Frame SectionFig. 37Fig. 39Fig. 38Fig. 40DISASSEMBLING1) After removing Switch box, place the Frame sec

P 16/ 30Repair[3] DISASSEMBLY/ASSEMBLY[3] -8. Frame Section (cont.)ASSEMBLINGFig. 41Fig. 42 Fig. 431) Fasten Screw M10 to left Frame/ right Frame so t

Hex bolt M6x45Flat washer 6P 17/ 30Repair[3] DISASSEMBLY/ASSEMBLY[3] -9. Assembling Feet SectionFig. 44 Fig. 451) For smooth folding action of the Fee

P 18/ 30 Repair[3] DISASSEMBLY/ASSEMBLY[3] -9. Assembling Feet Section (cont.)Fig. 484) To Square pipe 32-510, assemble Hook and Foot. And to Square p

P 19/ 30 Repair[3] DISASSEMBLY/ASSEMBLY[3] -10. Assembling Feet Section to Frame SectionFig. 50Fig. 51With eight M8x20 Hex socket bolts, fasten the le

P 2 / 30Standard equipmentAssorted TCT saw bladesNote: The standard equipment for the tool shown above may differ by country.TCT saw blade ... 1

P 20/ 30 Repair[4] ADJUSTMENT[4] -1. Adjusting Bevel AngleFig. 52 Fig. 53Fig. 54 Fig. 551) Lock the saw head unit in the full down position, and loose

P 21/ 30Repair[4] ADJUSTMENT[4] -2. Adjusting Miter AngleFig. 56 Fig. 571) Lock the saw head unit in the full down position.2) Slightly loosen four M6

Circuit diagramP 22/ 30All European Countries Except UK-110VColor index of lead wires' sheathBlackWhiteRedOrangeBlueBrown Purple YellowA1313141A2

Circuit diagramP 23/ 30UK-110VColor index of lead wires' sheathBlackWhiteRedOrangeBlueBrown Purple Yellow*Pick up coil is factory-assembled to Co

P 24/ 30Wiring diagramLead wire holder DMotor housingMotor housingChoke coil,connected with ControllerChoke coilControllerControllerOpening BOpening A

P 25/ 30Wiring diagram[2] Wiring in HandleAll European Countries Except UK-110VSwitchLine filterStrain relief10 - 20mm10 - 20mmConnecting cordfrom Swi

P 26/ 30Wiring diagram[3] Wiring in Switch BoxAll European Countries Except UK-110VSwitch boxGrommetConnecting cord from HandlePower supply cordRelayW

P 27/ 30Wiring diagram[4] Wiring at Connecting RodAll Countries[5] Wiring Under TableSwitch boxGrommetStrain reliefPan head screwM4x10Frame completeCo

P 28/ 30Wiring diagramLead wire holder DMotor housingMotor housingChoke coil,connected with ControllerChoke coilControllerControllerOpening BOpening A

P 29/ 30Wiring diagram[2] Wiring in HandleUK-110VSwitchLine filterStrain relief10 - 20mm10 - 20mmConnecting cordfrom Switch boxL-shaped ribInside wall

P 3 / 30 Repair[1] NECESSARY REPAIRING TOOLSCAUTION: Remove the saw blade from the machine for safety before repair/ maintenance ! Code No.1R003 Retai

P 30/ 30Wiring diagram[3] Wiring in Switch BoxUK-110VSwitch boxGrommetConnecting cord from HandlePower supply cordRelayWhen mounting Grommet to Switch

P 4 / 30 Repair[2] LUBRICATION (cont.)Apply Makita grease N. No.1 to the following portions designated with the black triangle to protectparts and pro

P 5 / 30 Repair[3] DISASSEMBLY/ASSEMBLY[3] -1. Handle SectionFig. 4Fig. 3Fig. 5DISASSEMBLINGThe Handle section can be disassembled without separating

P 6 / 30Repair[3] DISASSEMBLY/ASSEMBLYDISASSEMBLINGASSEMBLING[3] -2. Switch Box (On/Off Switch Section)Do the reverse of the disassembling steps. Fig.

P 7 / 30 Repair[3] DISASSEMBLY/ASSEMBLY[3] -3. Motor HousingFig. 12Fig. 13DISASSEMBLINGFig. 11Motor housing1) Remove Brush holder caps and Carbon brus

P 8 / 30 Repair[3] DISASSEMBLY/ASSEMBLY[3] -4. Gear SectionFig. 17Fig. 15Fig. 18DISASSEMBLINGFig. 141) Disconnect Tension spring 4 from Blade case.

P 9 / 30 Repair[3] DISASSEMBLY/ASSEMBLY[3] -5. Blade Case SectionFig. 21 Fig. 22DISASSEMBLINGFig. 19 Fig. 201) Remove Safety cover as illustrated in F