Makita DHP458 User Manual download pdf (Page 9)

Use a screwdriver to remove two screws then remove the

rear cover. (Fig. 18)

Raise the arm part of the spring and then place it in the

recessed part of the housing with a slotted bit screwdriver

of slender shaft or the like. (Fig. 19)

Use pliers to remove the carbon brush caps of the carbon

brushes. Take out the worn carbon brushes, insert the

new ones and replace the carbon brush caps in reverse.

(Fig. 20)

Make sure that the carbon brush caps have fit into the

holes in brush holders securely. (Fig. 21)

Reinstall the rear cover and tighten two screws securely.

To maintain product SAFETY and RELIABILITY, repairs,

any other maintenance or adjustment should be

performed by Makita Authorized Service Centers, always

using Makita replacement parts.

OPTIONAL ACCESSORIES

CAUTION:

• These accessories or attachments are recommended

for use with your Makita tool specified in this manual.

The use of any other accessories or attachments might

present a risk of injury to persons. Only use accessory

or attachment for its stated purpose.

If you need any assistance for more details regarding

these accessories, ask your local Makita Service Center.

• Drill bits

• Hammer drill bits

• Screw bits

• Blow-out bulb

• Safety goggles

• Makita genuine battery and charger

• Grip assembly

•Depth rod

•Hook

• Rubber pad assembly

• Wool bonnet

• Foam polishing pad

• Battery protector

NOTE:

• Some items in the list may be included in the tool

package as standard accessories. They may differ

from country to country.

Noise

ENG905-1

The typical A-weighted noise level determined according

to EN60745:

Model DHP448

Sound pressure level (L

): 82 dB (A)

Sound power level (L

): 93 dB (A)

Uncertainty (K): 3 dB (A)

Model DHP458

Sound pressure level (L

): 84 dB (A)

Sound power level (L

): 95 dB (A)

Uncertainty (K): 3 dB (A)

Wear ear protection.

Vibration

ENG900-1

The vibration total value (tri-axial vector sum) determined

according to EN60745:

Model DHP448

Work mode: impact drilling into concrete

Vibration emission (a

h,ID

): 8.5 m/s

Uncertainty (K): 1.5 m/s

Work mode: drilling into metal

Vibration emission (a

h,D

): 2.5 m/s

or less

Uncertainty (K): 1.5 m/s

Model DHP458

Work mode: impact drilling into concrete

Vibration emission (a

h,ID

): 9.5 m/s

Uncertainty (K): 1.5 m/s

Work mode: drilling into metal

Vibration emission (a

h,D

): 2.5 m/s

or less

Uncertainty (K): 1.5 m/s

ENG901-1

• The declared vibration emission value has been

measured in accordance with the standard test method

and may be used for comparing one tool with another.

• The declared vibration emission value may also be

used in a preliminary assessment of exposure.

WARNING:

• The vibration emission during actual use of the power

tool can differ from the declared emission value

depending on the ways in which the tool is used.

• Be sure to identify safety measures to protect the

operator that are based on an estimation of exposure in

the actual conditions of use (taking account of all parts

of the operating cycle such as the times when the tool

is switched off and when it is running idle in addition to

the trigger time).

For European countries only

ENH101-17

EC Declaration of Conformity

Makita declares that the following Machine(s):

Designation of Machine:

Cordless Hammer Driver Drill

Model No./Type: DHP448, DHP458

Conforms to the following European Directives:

2006/42/EC

They are manufactured in accordance with the following

Standard or standardized documents:

EN60745

The Technical file in accordance with 2006/42/EC is

available from:

Makita, Jan-Baptist Vinkstraat 2, 3070, Belgium

31. 12. 2013

Yasushi Fukaya

Director

Makita, Jan-Baptist Vinkstraat 2, 3070, Belgium

1 2 3 4 5 6 7 8 9 10 ... 64

Comments to this Manuals

No comments

Makita DHP458 User Manual Page 9

Comments to this Manuals

Related products and manuals for Power drills Makita DHP458