Makita UH6580 Instruction Manual download pdf (Page 5)

ENGLISH (Original instructions)

Explanation of general view

1-1. Switch trigger B

1-2. Switch trigger A

1-3. Switch trigger C

5-1. Hook complete

5-2. Tool's cord

5-3. Extension cord

6-1. Holder

6-2. Cord

7-1. Holder

7-2. Arm cord hook

11-1. Trimming direction

11-2. Tilt the blades

11-3. Hedge surface to be trimmed

16-1. Press

16-2. Chip receiver

16-3. Nut

16-4. Shear blade

17-1. Nut

17-2. Branch catcher

18-1. Hooks

18-2. Fit the hooks into groove

18-3. Grooves

19-1. Press the hooks on both sides

19-2. Unlock the hooks

20-1. Screws

20-2. Blade cover

21-1. Under cover

21-2. Blade cover

22-1. Gear housing cover

23-1. Crank

24-1. Screws

24-2. Shear blade

25-1. Crank

26-1. Ellipse of shear blade

28-1. Ellipse of shear blade

28-2. Crank

29-1. Crank

SPECIFICATIONS

Model UH5580 UH6580 UH7580

Blade length 550 mm 650 mm 750 mm

Strokes per minute (min

-1

) 1,500 1,500 1,500

Overall length 970 mm 1,049 mm 1,157 mm

Net weight 4.3 kg 4.4 kg 4.6 kg

Safety class /II

• Due to our continuing programme of research and development, the specifications herein are subject to change without notice.

• Specifications may differ from country to country.

• Weight according to EPTA-Procedure 01/2003

END220-4

Symbol

The following show the symbols used for the equipment.

Be sure that you understand their meaning before use.

･ Read instruction manual.

･ DOUBLE INSULATION

･ Do not expose to rain.

･ Remove plug from the mains

immediately if the cable is damaged or

cut.

･ Only for EU countries

Do not dispose of electric equipment

together with household waste material!

In observance of European Directive

2002/96/EC on waste electric and

electronic equipment and its

implementation in accordance with

national law, electric equipment that

have reached the end of their life must

be collected separately and returned to

an environmentally compatible

recycling facility.

ENE014-1

Intended use

The tool is intended for trimming hedges.

ENF002-1

Power supply

The tool should be connected only to a power supply of

the same voltage as indicated on the nameplate, and

can only be operated on single-phase AC supply. They

are double-insulated in accordance with European

Standard and can, therefore, also be used from sockets

without earth wire.

ENG102-3

Noise

The typical A-weighted noise level determined according

to EN60745:

Sound pressure level (L

) : 86.5 dB(A)

Sound power level (L

) : 94.5 dB(A)

Uncertainty (K) : 0.7 dB(A)

Wear ear protection

ENG231-1

Vibration

The vibration total value (tri-axial vector sum)

determined according to EN60745:

Work mode : hedge trimming

Vibration emission (a

) : 4.4 m/s

Uncertainty (K) : 1.5 m/s

ENG901-1

•

The declared vibration emission value has been

measured in accordance with the standard test

method and may be used for comparing one tool

1 2 3 4 5 6 7 8 9 10 ... 55 56

Comments to this Manuals

No comments

Makita UH6580 Instruction Manual Page 5

Comments to this Manuals

Related products and manuals for Grass trimmers Makita UH6580