Makita XT252T Use and Care Manual Page 40
- Page / 64
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
8
Adjustable depth rod
1
2
014821
The adjustable depth rod is used to drill holes of uniform
depth. Loosen the clamp screw, set to desired position,
then tighten the clamp screw.
Hook
1
2
3
014701
The hook is convenient for temporarily hanging the tool.
This can be installed on either side of the tool.
To install the hook, insert it into a groove in the tool
housing on either side and then secure it with a screw.
To remove, loosen the screw and then take it out.
OPERATION
014702
Hammer drilling operation
CAUTION:
• There is a tremendous and sudden twisting force
exerted on the tool/bit at the time of hole break-
through, when the hole becomes clogged with
chips and particles, or when striking reinforcing
rods embedded in the concrete. Always use the
side grip (auxiliary handle) and firmly hold the tool
by both side grip and switch handle during
operations. Failure to do so may result in the loss
of control of the tool and potentially severe injury.
First, slide the action mode change lever so that it
points to the
marking. The adjusting ring can be
aligned in any torque levels for this operation.
Be sure to use a tungsten-carbide tipped bit.
Position the bit at the desired location for the hole, then
pull the switch trigger. Do not force the tool. Light
pressure gives best results. Keep the tool in position
and prevent it from slipping away from the hole.
Do not apply more pressure when the hole becomes
clogged with chips or particles. Instead, run the tool at
an idle, then remove the bit partially from the hole. By
repeating this several times, the hole will be cleaned out
and normal drilling may be resumed.
Blow-out bulb (optional accessory)
1
002449
After drilling the hole, use the blow-out bulb to clean the
dust out of the hole.
Screwdriving operation
First, slide the action mode change lever so that it
points to the
marking. Adjust the adjusting ring to the
proper torque level for your work. Then proceed as
follows.
Place the point of the driver bit in the screw head and
apply pressure to the tool. Start the tool slowly and then
increase the speed gradually. Release the switch trigger
as soon as the clutch cuts in.
NOTE:
• Make sure that the driver bit is inserted straight in
the screw head, or the screw and/or bit may be
damaged.
• When driving wood screw, predrill a pilot hole 2/3
the diameter of the screw. It makes driving easier
and prevents splitting of the workpiece.
• If the tool is operated continuously until the battery
cartridge has discharged, allow the tool to rest for
15 minutes before proceeding with a fresh battery.
1. Blow-out bulb
1. Groove
2. Hook
3. Screw
1. Depth rod
2. Clamp screw
- Cordless Impact Driver 1
- Tournevis à Chocs sans Fil 1
- SPECIFICATIONS 2
- General Power Tool Safety 2
- Warnings 2
- Save all warnings and 2
- CORDLESS IMPACT DRIVER 3
- SAFETY WARNINGS 3
- SAVE THESE INSTRUCTIONS 3
- Changing the hammering force 6
- Empty signal for remaining 7
- TROUBLESHOOTING 9
- EN0006-1 10
- GEA006-2 11
- AVERTISSEMENT: 13
- Interrupteur 15
- Frein électrique 15
- Allumage de la lampe avant 15
- Inverseur 15
- Modification de la force de 16
- Crochet 17
- UTILISATION 18
- ENTRETIEN 18
- DÉPANNAGE 19
- ACCESSOIRES EN OPTION 19
- ADVERTENCIA: 23
- Freno eléctrico 25
- Señal de capacidad vacía de 26
- ENSAMBLE 27
- OPERACIÓN 28
- MANTENIMIENTO 28
- RESOLUCIÓN DE PROBLEMAS 29
- ACCESORIOS OPCIONALES 29
- ADVERTENCIA 32
- Cordless Hammer Driver Drill 33
- Perceuse Percussion-Visseuse 33
- Rotomartillo Atornillador 33
- Inalámbrico 33
- CORDLESS HAMMER DRIVER 35
- DRILL SAFETY WARNINGS 35
- WARNING: 36
- FUNCTIONAL DESCRIPTION 37
- ASSEMBLY 39
- OPERATION 40
- MAINTENANCE 41
- OPTIONAL ACCESSORIES 41
- CONSERVEZ CE MODE 46
- D'EMPLOI 46
- DESCRIPTION DU 46
- FONCTIONNEMENT 46
- État du voyant DEL 47
- Environ 50 % ou plus 47
- De 20 à 50 % environ 47
- Environ 20 % 47
- Changement de vitesse 48
- ASSEMBLAGE 49
- GUARDE ESTAS 56
- INSTRUCCIONES 56
- DESCRIPCIÓN DEL 56
- FUNCIONAMIENTO 56
- Cambio de velocidad 58
Related products and manuals for Cordless combi drills Makita XT252T
(60 pages)Danby DDR45B1GP Handbücher
Bedienungsanleitungen und Benutzerhandbücher für Luftentfeuchter Danby DDR45B1GP.
Wir stellen 1 PDF-Handbücher Danby DDR45B1GP zum kostenlosen herunterladen nach Dokumenttypen zur Verfügung Bedienungsanleitung
Comments to this Manuals