Makita GA7030S User Manual download pdf (Page 5)

ENGLISH

Explanation of general view

SPECIFICATIONS

• Due to our continuing program of research and development, the specifications herein are subject to change

without notice.

• Note: Specifications may differ from country to country.

Symbols

END202-2

The following show the symbols used for the tool. Be sure

that you understand their meaning before use.

................ Read instruction manual.

................ DOUBLE INSULATION

................ Wear safety glasses.

Intended use

The tool is intended for grinding, sanding and cutting of

metal and stone materials without the use of water.

Power supply

The tool should be connected only to a power supply of

the same voltage as indicated on the nameplate, and can

only be operated on single-phase AC supply. They are

double-insulated in accordance with European Standard

and can, therefore, also be used from sockets without

earth wire.

For public low-voltage distribution systems of

between 220 V and 250 V.

Switching operations of electric apparatus cause voltage

fluctuations. The operation of this device under unfavor-

able mains conditions can have adverse effects to the

operation of other equipment. With a mains impedance

equal or less than 0.25 Ohms it can be presumed that

there will be no negative effects. The mains socket used

for this device must be protected with a fuse or protective

circuit breaker having slow tripping characteristics.

ADDITIONAL SAFETY RULES

ENB031-6

1. Always use eye and ear protection. Other personal

protective equipment such as dust mask, gloves,

helmet and apron should be worn.

2. Always be sure that the tool is switched off and

unplugged before carrying out any work on the

tool.

3. Keep guards in place.

4. Use only wheels with correct size and wheels hav-

ing a maximum operating speed at least as high as

the highest No Load Speed marked on the tool’s

nameplate. When using depressed center wheels,

be sure to use only fiberglass-reinforced wheels.

5. Check the wheel carefully for cracks or damage

before operation. Replace cracked or damaged

wheel immediately.

6. Observe the instructions of the manufacturer for

correct mounting and use of wheels. Handle and

store wheels with care.

7. Do not use separate reducing bushings or adap-

tors to adapt large hole abrasive wheels.

8. Use only flanges specified for this tool.

9. Do not damage the spindle, the flange (especially

the installing surface) or the lock nut. Damage to

these parts could result in wheel breakage.

1. Shaft lock

2. Motor housing

3. Lock button

4. Handle

5. Switch trigger

6. Lock lever

7. Wheel guard

8. Screw

9. Bearing box

10. Nut

11. Lever

12. Lock nut

13. Depressed center wheel

14. Super flange

15. Inner flange

16. Lock nut wrench

17. Outer flange 78

18. Cut-off wheel

19. Inner flange 78

20. Dust collecting wheel guard

21. Exhaust vent

22. Inhalation vent

23. Commutator

24. Insulating tip

25. Carbon brush

26. Brush holder cap

27. Screwdriver

Model

GA7030/GA7030F/

GA7030S/GA7030SF

GA7040S/GA7040SF

GA9030/GA9030F/

GA9030S/GA9030SF

GA9040S/GA9040SF

Depressed center wheel

diameter

180 mm 230 mm

Spindle thread M14 M14

No load speed (min

-1

) 8,500 6,600

Overall length 511 mm 511 mm

Net weight 5.1 kg 5.5 kg 5.1 kg 5.5 kg

Safety class /II

1 2 3 4 5 6 7 8 9 10 ... 63 64

Comments to this Manuals

No comments

Makita GA7030S User Manual Page 5

Comments to this Manuals

Related products and manuals for Straight grinders Makita GA7030S