Makita 9207SPB User Manual download pdf (Page 4)

30.1.2009

000230

Tomoyasu Kato

Director

Makita Corporation

3-11-8, Sumiyoshi-cho,

Anjo, Aichi, 446-8502, JAPAN

GEA010-1

General Power Tool Safety

Warnings

WARNING Read all safety warnings and all

instructions. Failure to follow the warnings and

instructions may result in electric shock, fire and/or

serious injury.

Save all warnings and instructions for

future reference.

GEB038-3

POLISHER SAFETY WARNINGS

Safety Warnings Common for Polishing Operation:

1. This power tool is intended to function as a

polisher. Read all safety warnings,

instructions, illustrations and specifications

provided with this power tool. Failure to follow

all instructions listed below may result in electric

shock, fire and/or serious injury.

2. Operations such as grinding, sanding, wire

brushing or cutting-off are not recommended

to be performed with this power tool.

Operations for which the power tool was not

designed may create a hazard and cause

personal injury.

3. Do not use accessories which are not

specifically designed and recommended by

the tool manufacturer. Just because the

accessory can be attached to your power tool, it

does not assure safe operation.

4. The rated speed of the accessory must be at

least equal to the maximum speed marked on

the power tool. Accessories running faster than

their rated speed can break and fly apart.

The outside diameter and the thickness of your

accessory must be within the capacity rating of

your power tool.

Incorrectly sized accessories

cannot be adequately guarded or controlled.

6. Threaded mounting of accessories must

match the tool spindle thread. For

accessories mounted by flanges, the arbour

hole of the accessory must fit the locating

diameter of the flange. Accessories that do not

match the mounting hardware of the power tool

will run out of balance, vibrate excessively and

may cause loss of control.

7. Do not use a damaged accessory. Before each

use inspect the accessory such as backing

pad for cracks, tear or excess wear. If power

tool or accessory is dropped, inspect for

damage or install an undamaged accessory.

After inspecting and installing an accessory,

position yourself and bystanders away from

the plane of the rotating accessory and run

the power tool at maximum no-load speed for

one minute. Damaged accessories will normally

break apart during this test time.

8. Wear personal protective equipment.

Depending on application, use face shield,

safety goggles or safety glasses. As

appropriate, wear dust mask, hearing

protectors, gloves and workshop apron

capable of stopping small abrasive or

workpiece fragments. The eye protection must

be capable of stopping flying debris generated by

various operations. The dust mask or respirator

must be capable of filtrating particles generated

by your operation. Prolonged exposure to high

intensity noise may cause hearing loss.

9. Keep bystanders a safe distance away from

work area. Anyone entering the work area

must wear personal protective equipment.

Fragments of workpiece or of a broken accessory

may fly away and cause injury beyond immediate

area of operation.

10. Position the cord clear of the spinning

accessory. If you lose control, the cord may be

cut or snagged and your hand or arm may be

pulled into the spinning accessory.

11. Never lay the power tool down until the

accessory has come to a complete stop. The

spinning accessory may grab the surface and pull

the power tool out of your control.

12. Do not run the power tool while carrying it at

your side. Accidental contact with the spinning

accessory could snag your clothing, pulling the

accessory into your body.

13. Regularly clean the power tool’s air vents. The

motor’s fan will draw the dust inside the housing

and excessive accumulation of powdered metal

may cause electrical hazards.

14. Do not operate the power tool near flammable

materials. Sparks could ignite these materials.

15. Do not use accessories that require liquid

coolants. Using water or other liquid coolants

may result in electrocution or shock.

Kickback and Related Warnings

Kickback is a sudden reaction to a pinched or snagged

rotating wheel, backing pad, brush or any other

accessory. Pinching or snagging causes rapid stalling of

the rotating accessory which in turn causes the

uncontrolled power tool to be forced in the direction

opposite of the accessory’s rotation at the point of the

binding.

1 2 3 4 5 6 7 8 9 ... 43 44

Comments to this Manuals

No comments

Makita 9207SPB User Manual Page 4

Comments to this Manuals

Related products and manuals for Power sanders Makita 9207SPB