Makita XT405 Use and Care Manual download pdf (Page 72)

Screwdriving operation

011499

First, turn the action mode changing ring so that the

arrow on the tool body points to the

marking. Adjust

the adjusting ring to the proper torque level for your work.

Then proceed as follows.

Place the point of the driver bit in the screw head and

apply pressure to the tool. Start the tool slowly and then

increase the speed gradually. Release the switch trigger

as soon as the clutch cuts in.

CAUTION:

• Make sure that the driver bit is inserted straight in

the screw head, or the screw and/or bit may be

damaged.

NOTE:

• When driving wood screws, predrill pilot holes to

make driving easier and to prevent splitting of the

workpiece. See the chart.

Nominal diameter of wood screw Recommended size of pilot hole

3.1mm (1/8") 2.0mm - 2.2mm (5/64" - 3/32")

3.5mm (9/64") 2.2mm - 2.5mm (3/32" - 3/32")

3.8mm (5/32") 2.5mm - 2.8mm (3/32" - 7/64")

4.5mm (11/64") 2.9mm - 3.2mm (7/64" - 1/8")

4.8mm (3/16") 3.1mm - 3.4mm (1/8" - 9/64")

5.1mm (13/64") 3.3mm - 3.6mm (1/8" - 9/64")

5.5mm (7/32") 3.7mm - 3.9mm (9/64" - 5/32")

5.8mm (7/32") 4.0mm - 4.2mm (5/32" - 11/64")

6.1mm (15/64") 4.2mm - 4.4mm (11/64" - 11/64")

006576

Drilling operation

First, turn the adjusting ring so that the pointer points to

the

marking. Then proceed as follows.

CAUTION:

• Pressing excessively on the tool will not speed up

the drilling. In fact, this excessive pressure will only

serve to damage the tip of your bit, decrease the

tool performance and shorten the service life of the

tool.

• There is a tremendous force exerted on the tool/bit

at the time of hole break through. Hold the tool

firmly and exert care when the bit begins to break

through the workpiece.

• A stuck bit can be removed simply by setting the

reversing switch to reverse rotation in order to back

out. However, the tool may back out abruptly if you

do not hold it firmly.

• Always secure small workpieces in a vise or with a

similar hold-down device.

• If the tool is operated continuously until the battery

cartridge has discharged, allow the tool to rest for

15 minutes before proceeding with a fresh battery.

Drilling in wood

When drilling in wood, the best results are obtained with

wood drills equipped with a guide screw. The guide screw

makes drilling easier by pulling the bit into the workpiece.

Drilling in metal

To prevent the bit from slipping when starting to make a

hole, make an indentation with a center-punch and

hammer at the point to be drilled. Place the point of the bit

in the indentation and start drilling.

Use a cutting lubricant when drilling metals. The

exceptions are iron and brass which should be drilled dry.

MAINTENANCE

CAUTION:

• Always be sure that the tool is switched off and the

battery cartridge is removed before attempting to

perform inspection or maintenance.

• Never use gasoline, benzine, thinner, alcohol or the

like. Discoloration, deformation or cracks may

result.

Replacing the carbon brushes

006258

Replace when they wear down to the limit mark. Keep

the carbon brushes clean and free to slip in the holders.

Both carbon brushes should be replaced at the same

time. Use only identical carbon brushes.

Use a screwdriver to remove two screws then remove

the rear cover.

1. Limit mark

1 ... 71 72 73 ... 108

Comments to this Manuals

No comments

Makita XT405 Use and Care Manual Page 72

Comments to this Manuals

Related products and manuals for Power tools Makita XT405