Makita 6834 Instruction Manual download pdf (Page 5)

ENGLISH

Explanation of general view

1Lever

2 Stopper base

3Plate

4 Casing

5 Approx. 5 mm

6 Adjusting knob

7 Feeder box

8 Screw strip

9 Screw guide

10 Driving position

11 Reverse button

12 Hook

13 Lock button

14 Switch trigger

15 Reversing switch

16 Thumb screws

17 Bit

18 Dust cover

19 Plain bearing

20 Wall

21 Extension handle

22 Limit mark

23 Screwdriver

24 Brush holder cap

SPECIFICATIONS

Model 6833 6834 6836

Screw strip .......................................4 mm x 25 mm – 41 mm 4 mm x 25 mm – 57 mm 4 mm x 25 mm – 41 mm

No load speed (min

-1

) ......................4,700 2,800 6,000

Overall length ..................................364 mm 396 mm 364 mm

Net weight ........................................1.9 kg 1.9 kg 1.9 kg

• Due to our continuing program of research and devel-

opment, the specifications herein are subject to change

without notice.

• Note: Specifications may differ from country to country.

Intended use

The tool is intended for screw driving in wood, metal and

plastic.

Power supply

The tool should be connected only to a power supply of

the same voltage as indicated on the nameplate, and can

only be operated on single-phase AC supply. They are

double-insulated in accordance with European Standard

and can, therefore, also be used from sockets without

earth wire.

Safety hints

For your own safety, please refer to the enclosed safety

instructions.

ADDITIONAL SAFETY RULES

1. Hold tool by insulated gripping surfaces when

performing an operation where the cutting tools

may contact hidden wiring or its own cord. Con-

tact with a “live” wire will make exposed metal

parts of the tool “live” and shock the operator.

2. Always be sure you have a firm footing. Be sure

no one is below when using the tool in high loca-

tions.

3. Hold the tool firmly.

4. Keep hands away from rotating parts.

5. Do not leave the tool running. Operate the tool

only when hand-held.

6. Do not touch the drill bit or the workpiece imme-

diately after operation; they may be extremely

hot and could burn your skin.

SAVE THESE INSTRUCTIONS.

OPERATING INSTRUCTIONS

Setting for desired screw length (Fig. 1)

There are 3 (for Model 6833 & 6836) or 5 (for

Model 6834) positive-lock screw length settings. To

obtain the desired setting, pull out the stopper base while

depressing the lever until you see the number of the

desired screw length (indicated on the plate) appear to

rest on the very top edge of the casing. See the table

below for the relation between the number indicated on

the plate and the respective screw length ranges.

(Note) * for Model 6834 only

Adjusting the driving depth (Fig. 2)

Depress the stopper base as far as it will go. While keep-

ing it in this position, turn the adjusting knob until the bit

tip projects approx. 5 mm from the stopper base. Drive a

trial screw. If the screw head projects above the surface

of the workpiece, turn the adjusting knob in the A direc-

tion; if the screw head is countersunk, turn the adjusting

knob in the B direction.

Installing screw strip (Fig. 3 & 4)

Insert the screw strip through the screw guide. Then

insert it through the feeder box until the first screw

reaches the position next to the driving position.

Removing screw strip (Fig. 5 & 6)

To remove the screw strip, just pull it out in the direction

of the arrow. If you depress the reverse button, you can

pull out the screw strip in the reverse direction of the

arrow.

Number indicated

on the plate

Screw length range

(mm)

25/28 25 – 28

32 28 – 35

40 35 – 41

*51 41 – 51

*57 51 – 57

1 2 3 4 5 6 7 8

Comments to this Manuals

No comments

Makita 6834 Instruction Manual Page 5

Comments to this Manuals

Related products and manuals for Power tools Makita 6834