Makita RBC252 User Manual

Brush Cutter RBC252 String Trimmer RBC253 INSTRUCTION MANUAL RBC252 Read i uies for operation z-irld instrucirons carefully

ENGINE STARTING AND STOPPING PROCEDURES Starting when the engine is cold Use the following procedure when the engine is cold 01 after It has beer, st

CORRECT HANDLING OF THE MACHINE I ... .. ~- ~- - i- Fig 22 Fig. 21 Attachment, adjustment and detachment of the shoulder strap Attachment Place the st

Handling the machine 1. Hang the machine on the right side of your body 2 Squeeze the throttle lever to increase the rotational speed Release the th

DAlLY CHECK-UP AND MAINTENANCE cover Fig. 27 06 mm - 07 mm (0024' - 0028") I Fig. 29 , I Sponge element - FIY 28 I x I Fig. 30 1. Before ope

i STORAGE When storing the machine for a icng time drain the fuel from the fuel tank and cdrbLretor as follows ' 1 2 3 Drain all fuel from

INSTRUCTIONS FOR USE OF THE CUTTER BLADE safety instructions 1. Read this section carefully and thoroughly before use 2 Check the blade before use (F

Kickback Prevention To avoid kickbacks, observe the following: Easy cutting with almost no kickback is possible with- in a blade segment between 8 an

INSTRUCTIONS FOR USE OF THE NYLON CUTTING HEAD (Model WBC253) (BUMP & FEED BF4) * I Safety Instructions 1 2 Read this section carefully and thorou

Replacing the nylon cord (Bump & Feed BF4) 1. Press the homing latches inward to lift off the cover; then remove the spool (Fig. 44). 2. Run the n

Emmision Control Warranty Statement YOUR WARRANTY RIGHTS AND OBLIGATIONS The California Air Resources Board arid Makita U.S.A.. Inc. are pleased to ex

~ -- -~ Thank you very much for purchasing your MAKITA STRING TRIMMER ’ BRUSH CUTTER We are prclud of and very confident in recommending our MAKI

LllMlTED WARRANTY - California Only - Makita U S A Inc a distributor of utility and lawn and garden equipment in the U S , warrants to the owner of

WHAT IS NOT COVERED UNDER THIS WARRANTY Tills ivarrai?ty does not cover any emission-relatea part <>vITich m?l:i.J!i c;ns and/or modifications

REPAIR AND REPLACEMENT OF ERillSSIQN-RELATED PARTS It IS reccximericlerf thai Sniy engirie replacement parts which have beer aLtiic;r!zer: ?r-ifJ a

23 24 25 26 27 28 29 30 31 32 33 34 i 35 36 37 38 39 40 41 42 43 44. 45 46. Use only replacement parts that are identical to original equipment part

EQUIPMENT DESCRIPTION NO. _. - ~ 1 I FuelTank I Recoil Starter 2 Air Cleaner I ___ __ 3 4 TSTOP Switch -5 1 Spark Plug 6 --Muffler ---- 7 i Holder Cas

ASSEMBLY INSTRUCTIONS FOR STRING TRIMMER (Model RBC253) Mounting the handle (Fig. 1) 1 2 3 4 Attach the handle to the drive shaft Install the handle j

TProttle wire io throttle lever STEP 1 Flcj 9 Throttle wre ano Mounting the handle and connecting the throttle wire and switch cords. 1 klatch the pro

ASSEMBLY INSTRUCTIONS FOR BRUSH CUTTER (ModelRBC252) Mounting the protector (Fig. 11) 1. Install the clamp on the drive shaft so that the projection o

PREPARING FOR OPERATION Fuel and oil mixture This product is powered by a two-cycle engine and requires pre-mixing gasoline and two-cycle engine 011 I

REFUELING Use Oil-gasoline mixture for fuel as noted in "Fuel and Oil Mixture" on previous page Always shut off the engine and allow it to