Makita HR160D User Manual download pdf (Page 4)

ENGLISH

Explanation of general view

1 Set plate

2 Battery cartridge

3 Charging light

4 Battery charger

5 Bit shank

6Bit grease

7Bit

8 Chuk cover

9 Clamp screw

10 Side grip

11 Depth gauge

12 Reversing switch

13 Switch trigger

14 Action mode changing knob

15 Chisel adapter

16 Clamp screw

17 Chisel

18 Dust cup

19 Drill chuk assembly

SPECIFICATIONS

Model HR160D

Capacities

Concrete ............................................................ 16 mm

Steel ................................................................... 13 mm

Wood .................................................................. 20 mm

No load speed (min

-1

) .......................................... 0 – 950

Blows per minute ............................................... 0 – 3,600

Overall length ..................................................... 296 mm

Net weight ............................................................. 2.5 kg

Rated voltage ..................................................... D.C.12 V

• Due to our continuing program of research and devel-

opment, the specifications herein are subject to change

without notice.

• Note: Specifications may differ from country to country.

Safety hints

For your own safety, please refer to the enclosed safety

instructions.

IMPORTANT SAFETY INSTRUCTIONS FOR

CHARGER & BATTERY CARTRIDGE

ENC001-3

1. SAVE THESE INSTRUCTIONS — This manual

contains important safety and operating instruc-

tions for battery charger.

2. Before using battery charger, read all instruc-

tions and cautionary markings on (1) battery

charger, (2) battery, and (3) product using bat-

tery.

3. CAUTION — To reduce risk of injury, charge only

MAKITA type rechargeable batteries. Other types

of batteries may burst causing personal injury

and damage.

4. Do not expose charger to rain or snow.

5. Use of an attachment not recommended or sold

by the battery charger manufacturer may result

in a risk of fire, electric shock, or injury to per-

sons.

6. To reduce risk of damage to electric plug and

cord, pull by plug rather than cord when discon-

necting charger.

7. Make sure cord is located so that it will not be

stepped on, tripped over, or otherwise subjected

to damage or stress.

8. Do not operate charger with damaged cord or

plug — replace them immediately.

9. Do not operate charger if it has received a sharp

blow, been dropped, or otherwise damaged in

any way; take it to a qualified serviceman.

10. Do not disassemble charger or battery cartridge;

take it to a qualified serviceman when service or

repair is required. Incorrect reassembly may

result in a risk of electric shock or fire.

11. To reduce risk of electric shock, unplug charger

from outlet before attempting any maintenance

or cleaning. Turning off controls will not reduce

this risk.

12. The battery charger is not intended for use by

young children or infirm persons without super-

vision.

13. Young children should be supervised to ensure

that they do not play with the battery charger.

14. If operating time has become excessively

shorter, stop operating immediately. It may result

in a risk of overheating, possible burns and even

an explosion.

15. If electrolyte gets into your eyes, rinse them out

with clear water and seek medical attention right

away. It may result in loss of your eyesight.

ADDITIONAL SAFETY RULES FOR CHARGER

& BATTERY CARTRIDGE

1. Do not charge Battery Cartridge when tempera-

ture is BELOW 10°C (50°F) or ABOVE 40°C

(104°F).

2. Do not attempt to use a step-up transformer, an

engine generator or DC power receptacle.

3. Do not allow anything to cover or clog the

charger vents.

4. Always cover the battery terminals with the bat-

tery cover when the battery cartridge is not

used.

5. Do not short the battery cartridge:

(1) Do not touch the terminals with any conduc-

tive material.

(2) Avoid storing battery cartridge in a container

with other metal objects such as nails, coins,

etc.

(3) Do not expose battery cartridge to water or

rain.

A battery short can cause a large current flow,

overheating, possible burns and even a break-

down.

6. Do not store the tool and battery cartridge in

locations where the temperature may reach or

exceed 50°C (122°F).

7. Do not incinerate the battery cartridge even if it

is severely damaged or is completely worn out.

The battery cartridge can explode in a fire.

8. Be careful not to drop, shake or strike battery.

9. Do not charge inside a box or container of any

kind. The battery must be placed in a well venti-

lated area during charging.

1 2 3 4 5 6 7 8 9 ... 63 64

Comments to this Manuals

No comments

Makita HR160D User Manual Page 4

Comments to this Manuals

Related products and manuals for Rotary hammers Makita HR160D