Makita 9217SPC User Manual download pdf (Page 6)

OPERATING INSTRUCTIONS

Side grip (auxiliary handle) (Fig. 1)

For your own safety, always use the side grip. The

side grip can be installed on either side of the tool.

Switching ON and OFF (Fig. 2)

CAUTION:

Before plugging in the tool, always check to see that

the switch trigger actuates properly and returns to the

‘‘OFF’’ position when released.

To switch on, press the trigger. To switch off, release

the trigger.

Continuous running (Fig. 2)

Press the trigger and at the same time push the lock

button. To stop this lock position, press the trigger and

release it.

Speed change

For 9207SPB (Fig. 3)

The tool speed can be changed by moving the speed

change switch to the ‘‘L’’ position or ‘‘H’’ position.

High speed (3,800 min

-1

): For sanding operation

Low speed (2,000 min

-1

): For polishing operation

CAUTION:

Use the speed change switch only after the tool

comes to a complete stop.

For 9217SPC (Fig. 4)

The tool speed can be infinitely adjusted between

1,500 rpm and 2,800 rpm by turning the speed

change knob. Refer to the table below for relationship

between the number settings on the knob and the

approx. tool speed.

High speed: For sanding operation

Low speed: For polishing operation

Number min

-1

1 1,500

2 1,750

3 2,000

4 2,300

5 2,550

6 2,800

CAUTION:

•

If the tool is operated continuously at low speeds for

a long time, the motor will get overloaded and

heated up.

•

The speed adjusting dial can be turned only as far

as 6 and back to 1. Do not force it past 6 or 1, or the

speed adjusting function may no longer work.

FOR USE AS A SANDER

Installing or removing the abrasive disc

(Fig.5&6)

Important:

Always be sure that the tool is switched off and

unplugged before installing or removing the disc.

Mount the rubber pad onto the spindle. Fit the disc on

over the rubber pad and screw the lock nut onto the

spindle. Hold the spindle firmly with the wrench and

tighten the lock nut using the lock nut wrench.

Sanding operation (Fig. 7)

Keep the abrasive disc at an angle of about 10° – 15°

to the workpiece surface. Apply slight pressure only.

Excessive pressure will result in poor performance

and premature wear to the abrasive disc.

FOR USE AS A POLISHER

Installing or removing the wool bonnet

(Fig. 8,9&10)

Important:

Always be sure that the tool is switched off and

unplugged before installing or removing the wool

bonnet.

Mount the rubber pad onto the spindle. Screw the lock

nut onto the spindle. Hold the spindle firmly with the

wrench and tighten the lock nut using the lock nut

wrench. Fit the wool bonnet over the rubber pad. Tie

a bow knot and tuck the knot and any loose strings

between the wool bonnet and the rubber pad.

Polishing operation (Fig. 11)

Keep the wool bonnet at an angle of about 10° – 15°

to the workpiece surface.

MAINTENANCE

CAUTION:

Always be sure that the tool is switched off and

unplugged before carrying out any work on the tool.

Replacement of carbon brushes

(Fig. 12 & 13)

Replace carbon brushes when they are worn down to

the limit mark. Both identical carbon brushes should

be replaced at the same time.

To maintain product safety and reliability, repairs,

maintenance or adjustment should be carried out by a

Makita Authorized Service Center.

1 2 3 4 5 6 7 8 9 10 11 ... 35 36

Comments to this Manuals

No comments

Makita 9217SPC User Manual Page 6

Comments to this Manuals

Related products and manuals for Power sanders Makita 9217SPC