Makita KP0800 Instruction Manual download pdf (Page 8)

connect a hose of the vacuum cleaner to the nozzle as

shown in the figures.

Elbow (optional accessory)

Fig.13

Use of elbow allows change of chip discharge direction

to perform cleaner work.

For tool without nozzle

Remove the chip cover and install the nozzle (optional

accessory). Attach the elbow (optional accessory) on the

nozzle of the tool by just slipping on it. To remove it,

just pull it out.

For tool with nozzle

Attach the elbow (optional accessory) on the nozzle of

the tool by just slipping on it. To remove it, just pull it out.

OPERATION

Hold the tool firmly with one hand on the knob and the

other hand on the switch handle when performing the

tool.

Planing operation

Fig.14

First, rest the tool front base flat upon the workpiece

surface without the blades making any contact. Switch

on and wait until the blades attain full speed. Then move

the tool gently forward. Apply pressure on the front of

tool at the start of planing, and at the back at the end of

planing. Planing will be easier if you incline the

workpiece in stationary fashion, so that you can plane

somewhat downhill.

The speed and depth of cut determine the kind of finish.

The power planer keeps cutting at a speed that will not

result in jamming by chips. For rough cutting, the depth

of cut can be increased, while for a good finish you

should reduce the depth of cut and advance the tool

more slowly.

Shiplapping (Rabbeting)

Fig.15

To make a stepped cut as shown in the figure, use the

edge fence (guide rule) which is obtained as accessory.

Fig.16

Draw a cutting line on the workpiece. Insert the edge

fence into the hole in the front of the tool. Align the blade

edge with the cutting line.

Fig.17

Adjust the edge fence until it comes in contact with the

side of the workpiece, then secure it by tightening the

screw.

Fig.18

When planing, move the tool with the edge fence flush

with the side of the workpiece. Otherwise uneven

planing may result.

Maximum shiplapping (rabbeting) depth is 9 mm.

Fig.19

You may wish to add to the length of the fence by

attaching an extra piece of wood. Convenient holes are

provided in the fence for this purpose, and also for

attaching an extension guide (optional accessory).

Chamfering

Fig.20

Fig.21

To make a chamfering cut as shown in the figure, align

the "V" groove in the front base with the edge of the

workpiece and plane it.

MAINTENANCE

CAUTION:

• Always be sure that the tool is switched off and

unplugged before attempting to perform inspection

or maintenance.

Sharpening the planer blades

For conventional blades only

Fig.22

Always keep your blades sharp for the best performance

possible. Use the sharpening holder (optional

accessory) to remove nicks and produce a fine edge.

Fig.23

First, loosen the two wing nuts on the holder and insert

the blades (A) and (B), so that they contact the sides (C)

and (D). Then tighten the wing nuts.

Fig.24

Immerse the dressing stone in water for 2 or 3 minutes

before sharpening. Hold the holder so that the both

blades contact the dressing stone for simultaneous

sharpening at the same angle.

Replacing carbon brushes

Fig.25

Remove and check the carbon brushes regularly.

Replace when they wear down to the limit mark. Keep

the carbon brushes clean and free to slip in the holders.

Both carbon brushes should be replaced at the same

time. Use only identical carbon brushes.

Fig.26

Fig.27

Use a screwdriver to remove the chip cover or nozzle.

Fig.28

Use a screwdriver to remove the brush holder caps.

Take out the worn carbon brushes, insert the new ones

and secure the brush holder caps.

To maintain product SAFETY and RELIABILITY, repairs,

any other maintenance or adjustment should be

performed by Makita Authorized Service Centers,

always using Makita replacement parts.

1 2 3 4 5 6 7 8 9 10 11 12 13 ... 55 56

Comments to this Manuals

No comments

Modely	Typ Dokumentu
THGD18	Uživatelský manuál York THGD18 User's Manual [fr] , 30 stránky
THJF60	Instalační manuál York THJF60 Installation manual, 14 stránky
TP9C	Instalační manuál York TP9C Installation manual, 46 stránky

Makita KP0800 Instruction Manual Page 8

Comments to this Manuals

York Tepelná čerpadla uživatelské příručky

Makita KP0800 Instruction Manual Page 8

Comments to this Manuals

Related products and manuals for Power planers Makita KP0800

York Tepelná čerpadla uživatelské příručky