Makita DCS 341 User Manual Page 21
- Page / 60
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
21
Refuelling
FOLLOW THE SAFETY PRECAUTIONS ON PAGE 7!
Be careful and cautious when handling fuels.
The engine must be switched off!
- Thoroughly clean the area around the plugs, to prevent dirt
from getting into the fuel or oil tank.
- Unscrew the plug and fill the tank with fuel (fuel/oil mixture)
or chain oil as the case may be. Fill up to the bottom edge
of the filler neck. Be careful not to spill fuel or chain oil!
- Tightly screw on the plug.
Clean screw plug and tank after refuelling.
Lubricating the chain
During operation there must always be sufficient chain oil in the
chain-oil tank to provide good chain lubrication. One filling is
sufficient for about one half-hour of continuous operation.
We recommend the use of chain oil which is bio-degradable in
order to protect the environment. The use of bio-degradable oil
may even be required by local regulations.
The chain oil BIOTOP sold by MAKITA is made of special
vegetable oils and is 100% bio-degradable. BIOTOP has been
granted the "blue angel" (Blauer Umweltschutz-Engel) for
being particularly environment-friendly (RAL UZ 48).
BIOTOP chain oil is available in the following sizes:
1 l order number 980 008 610
5 l order number 980 008 611
20 l order number 980 008 613
Bio-degradable oil is stable only for a limited period of time. It
should be used within 2 years from the date of manufacture
(printed on the container).
Important note on bio-degradable chain oils
If you are not planning to use the saw again for an extended
period of time (longer than the expiration date of the chain oil),
empty the oil tank and put in a small amount of regular engine
oil (SAE 30),and then run the saw for a time. This is necessary
to flush out all remaining bio-degradable oil from the oil tank,
oil-feed system, chain and guide bar, as many such oils tend
to leave sticky residues over time, which can cause damage to
the oil pump or other parts.
The next time you use the saw, fill the tank with BIOTOP chain
oil again.
G
fuel
chain oil
F
AVOID SKIN AND EYE CONTACT
Mineral oil products degrease your skin. If your skin comes in
contact with these substances repeatedly and for an extended
period of time, it will desiccate. Various skin deseases may
result. In addition, allergic reactions are known to occur.
Eyes can be irritated by contact with oil. If oil comes into your
eyes, immediately wash them with clear water.
If your eyes are still irritated, see a doctor immediately!
NEVER USE WASTE OIL
Waste oil is very dangerous for the environment.
Waste oil contains high amounts of carcinogenic substances.
Residues in waste oil result in a high degree of wear and tear
at the oil pump and the sawing device.
In case of damage caused by using waste oil or unappropriate
chain oil the product guarantee will be null and void.
Your salesman will inform you about the use of chain oil.
E
waste oil
STOP
- Owner’s and 1
- Safety Manual 1
- Manuel d’emploi 1
- WARNING ! 2
- Additional safety precautions 4
- Proper clothing 6
- 10 feet 7
- Important adjustments 8
- Kickback: 9
- Saw chain cutter sharpness: 10
- To avoid kickback 10
- Cutting techniques 11
- " 12
- Maintenance and Repair 15
- DCS 401 16
- 16" (400mm) 16
- 9709 123456 16
- Serial no 16
- Tightening the saw chain 19
- Checking the chain tension 19
- Safety chain brake 20
- Fuel / Refuelling 20
- Refuelling 21
- AVOID SKIN AND EYE CONTACT 21
- NEVER USE WASTE OIL 21
- Stopping the engine 22
- Starting the engine 22
- Adjusting the carburetor 23
- Working in winter 24
- Sharpening the saw chain 24
- Cleaning the guide bar 25
- Replacing the suction head 26
- Replacing the saw chain 26
- Cleaning the air filter 27
- Replacing the spark plug 27
- Maintenance and repair 28
- Troubleshootig 29
- DCS 340 / DCS 341 30
- DCS 400 / DCS 401 30
- ATTENTION! 31
- XXX.YYY.ZZZ 34
- Quels vêtements porter? 35
- La tronçonneuse 35
- 10 pieds 36
- Réglages importants 37
- Conditions de travail 37
- Choc de recul (Kickback): 38
- Pour éviter le choc de recul 39
- Techniques de coupe 40
- Entretien et réparation 44
- Frein de chaîne 49
- Carburants/ravitaillement 49
- Remplissage des réservoirs 50
- SECURITE (PAGE 36)! 50
- Arrêter le moteur 51
- Démarrer le moteur 51
- Vérifier le frein de chaîne 52
- Réglage du carburateur 52
- Marche hivernale 53
- Affûtage de la chaîne 53
- Nouvelle chaîne de sciage 55
- Nettoyage du filtre d’air 56
- Remplacement de bougie 56
- Maintenance et réparations 57
- Pièces de rechange 58
- Garantie 58
- Recherche de pannes 58
- Changements sans préavis 60
Related products and manuals for Petrol tool Makita DCS 341
Petrol tool Makita UC4020A User Manual
(120 pages)
(120 pages)
Petrol tool Makita DCS642120 User Manual
(13 pages)
(13 pages)
Petrol tool Makita DCS34 User Manual
(9 pages)
(9 pages)
Petrol tool Makita UC4030A User Manual
(5 pages)
(5 pages)
Petrol tool Makita UC3020A User Manual
(2 pages)
(2 pages)
Petrol tool Makita DCS5200 User Manual
(64 pages)
(64 pages)
Petrol tool Makita UC120D User Manual
(48 pages)
(48 pages)
Petrol tool Makita UC4020A User Manual
(24 pages)
(24 pages)
Petrol tool Makita UC4030AP User Manual
(24 pages)
(24 pages)
Petrol tool Makita DCS4610-40 User Manual
(28 pages)
(28 pages)
Danby DDR45B1GP Handbücher
Bedienungsanleitungen und Benutzerhandbücher für Luftentfeuchter Danby DDR45B1GP.
Wir stellen 1 PDF-Handbücher Danby DDR45B1GP zum kostenlosen herunterladen nach Dokumenttypen zur Verfügung Bedienungsanleitung
Comments to this Manuals