Makita LS0815FL Instruction Manual download pdf (Page 19)

scale. Then turn the turn base slightly clockwise and

counterclockwise to seat the turn base in the 0° miter

notch. (Leave as it is if the pointer does not point to

0°.) Loosen the hex sockets bolts securing the guide

fence using the socket wrench. (Fig. 46)

Lower the handle fully and lock it in the lowered

position by pushing in the stopper pin. Square the side

of the blade with the face of the guide fence using a

triangular rule, try-square, etc. Then securely tighten

the hex socket bolts on the guide fence in order

starting from the right side. (Fig. 47)

Make sure that the pointer points to 0° on the miter

scale. If the pointer does not point to 0°, loosen the

screw which secures the pointer and adjust the pointer

so that it will point to 0°.

2. Bevel angle

(1) 0° bevel angle (Fig. 48)

Push the carriage toward the guide fence and

tighten the locking screw to secure the carriage.

Lower the handle fully and lock it in the lowered

position by pushing in the stopper pin. Loosen the

lever at the rear of the tool. (Fig. 49)

Turn the hex bolt on the right side of the arm two

or three revolutions counterclockwise to tilt the

blade to the right. (Fig. 50)

Carefully square the side of the blade with the top

surface of the turn base using the triangular rule,

try-square, etc. by turning the hex bolt on the right

side of the arm clockwise. Then tighten the lever

securely. (Fig. 51)

Make sure that the pointer on the arm point to 0°

on the bevel scale on the arm holder. If they do not

point to 0°, loosen the screw which secure the

pointer and adjust it so that it will point to 0°.

(2) 45° bevel angle (Fig. 52)

Adjust the 45° bevel angle only after performing 0°

bevel angle adjustment. To adjust left 45° bevel

angle, loosen the lever and tilt the blade to the left

fully. Make sure that the pointer on the arm points

to 45° on the bevel scale on the arm holder. If the

pointer does not point to 45°, turn the 45° bevel

angle adjusting bolt on the right side of the arm

holder until the pointer points to 45°.

To adjust the right 5° bevel angle, perform the

same procedure as that described above.

Replacing carbon brushes (Fig. 53)

Remove and check the carbon brushes regularly. Replace

when they wear down to 3 mm in length. Keep the carbon

brushes clean and free to slip in the holders. Both carbon

brushes should be replaced at the same time. Use only

identical carbon brushes. (Fig. 54)

Use a screwdriver to remove the brush holder caps. Take

out the worn carbon brushes, insert the new ones and

secure the brush holder caps.

After use

• After use, wipe off chips and dust adhering to the tool

with a cloth or the like. Keep the blade guard clean

according to the directions in the previously covered

section titled “Blade guard”. Lubricate the sliding

portions with machine oil to prevent rust.

• When storing the tool, pull the carriage toward you

fully.

To maintain product SAFETY and RELIABILITY, repairs,

any other maintenance or adjustment should be

performed by Makita Authorized Service Centers, always

using Makita replacement parts.

OPTIONAL ACCESSORIES

WARNING:

• These Makita accessories or attachments are

recommended for use with your Makita tool

specified in this manual. The use of any other

accessories or attachments may result in serious

personal injury.

• Only use the Makita accessory or attachment for its

stated purpose. Misuse of an accessory or

attachment may result in serious personal injury.

If you need any assistance for more details regarding

these accessories, ask your local Makita Service Center.

• Steel & Carbide-tipped saw blades

006526

• Vertical vise

• Socket wrench with hex wrench on its other end

• Holder

• Dust bag

• Triangular rule

NOTE:

• Some items in the list may be included in the tool

package as standard accessories. They may differ

from country to country.

Noise

ENG905-1

The typical A-weighted noise level determined according

to EN61029:

Sound pressure level (L

): 87 dB (A)

Sound power level (L

): 110 dB (A)

Uncertainty (K): 3 dB (A)

Wear ear protection.

Vibration

ENG900-1

The vibration total value (tri-axial vector sum) determined

according to EN61029:

Vibration emission (a

): 2.5 m/s

or less

Uncertainty (K): 1.5 m/s

ENG901-1

• The declared vibration emission value has been

measured in accordance with the standard test method

and may be used for comparing one tool with another.

• The declared vibration emission value may also be

used in a preliminary assessment of exposure.

Miter saw blades

For smooth and precise cutting in

various materials.

Combination

General purpose blade for fast and

smooth rip, crosscuts and miters.

Crosscutting

For smoother cross grain cuts. Slices

cleanly against the grain.

Fine cross cuts

For sand-free cuts cleanly against the

grain.

Non-ferrous

metals miter saw

blades

For miters in aluminum, copper,

brass, tubing, and other non-ferrous

metals.

1 2 ... 14 15 16 17 18 19 20 21 22 23 24 ... 131 132

Comments to this Manuals

No comments

Makita LS0815FL Instruction Manual Page 19

Comments to this Manuals

Related products and manuals for Mitre saws Makita LS0815FL