Makita RP0900K Instruction Manual download pdf (Page 6)

ENGLISH (Original instructions)

Explanation of general view

SPECIFICATIONS

• Due to our continuing programme of research and development, the specifications herein are subject to change without

notice.

• Specifications may differ from country to country.

• Weight according to EPTA-Procedure 01/2003

Intended use

ENE010-1

The tool is intended for flush trimming and profiling of

wood, plastic and similar materials.

Power supply

ENF002-1

The tool should be connected only to a power supply of

the same voltage as indicated on the nameplate, and can

only be operated on single-phase AC supply. They are

double-insulated in accordance with European Standard

and can, therefore, also be used from sockets without

earth wire.

General Power Tool Safety

Warnings GEA010-1

WARNING Read all safety warnings and all

instructions. Failure to follow the warnings and

instructions may result in electric shock, fire and/or

serious injury.

Save all warnings and

instructions for future reference.

ROUTER SAFETY WARNINGS

GEB018-2

1. Hold power tools by insulated gripping surfaces

when performing an operation where the cutting

tool may contact hidden wiring or its own cord.

Contact with a “live” wire will make exposed metal

parts of the tool “live” and shock the operator.

2. Use clamps or another practical way to secure and

support the workpiece to a stable platform.

Holding the work by hand or against your body leaves

it unstable and may lead to loss of control.

3. Wear hearing protection during extended period

of operation.

4. Handle the bits very carefully.

5. Check the bit carefully for cracks or damage

before operation. Replace cracked or damaged bit

immediately.

6. Avoid cutting nails. Inspect for and remove all

nails from the workpiece before operation.

7. Hold the tool firmly with both hands.

8. Keep hands away from rotating parts.

9. Make sure the bit is not contacting the workpiece

before the switch is turned on.

10. Before using the tool on an actual workpiece, let it

run for a while. Watch for vibration or wobbling

that could indicate improperly installed bit.

11. Be careful of the bit rotating direction and the feed

direction.

12. Do not leave the tool running. Operate the tool

only when hand-held.

13. Always switch off and wait for the bit to come to a

complete stop before removing the tool from

workpiece.

14. Do not touch the bit immediately after operation; it

may be extremely hot and could burn your skin.

15. Do not smear the tool base carelessly with

thinner, gasoline, oil or the like. They may cause

cracks in the tool base.

16. Draw attention to the need to use cutters of the

correct shank diameter and which are suitable for

the speed of the tool.

17. Some material contains chemicals which may be

toxic. Take caution to prevent dust inhalation and

skin contact. Follow material supplier safety data.

18. Always use the correct dust mask/respirator for

the material and application you are working with.

1. Stopper pole

2. Screw

3. Lock lever

4. Depth pointer

5. Adjusting hex bolt

6. Stopper block

7. Switch trigger

8. Workpiece

9. Bit revolving direction

10. View from the top of the tool

11. Feed direction

12. Straight guide

13. Guide bar

14. Clamp screw

15. Base

16. Templet guide

17. Bit

18. Templet

19. Distance (X)

20. Outside diameter of the templet

guide

21. Dust nozzle

22. Thumb screw

Model RP0900

Collet chuck capacity 6mm, 1/4”, 8 mm and/or 3/8”

Plunge capacity 0 - 35 mm

No load speed (min

-1

) 27,000

Overall height 217 mm

Net weight 2.7 kg

Safety class /II

1 2 3 4 5 6 7 8 9 10 11 ... 51 52

Comments to this Manuals

No comments

Makita RP0900K Instruction Manual Page 6

Comments to this Manuals