Makita 2030N Instruction Manual

Planer- Jointer Auto feed 320 mm (1242") MODEL 2030N With Electric Brake Width 0 mm - 150 mm 150 mm - 240 mm 240 mm - 320 mm High Low IO' -

OPE RATION 1. Auto-Planer Determine the depth of cut and the cutting speed in terms of the width of the work- piece you intend to cut. Insert the

Jointing edge Set the fence square with the table. Hold the best face of the workpiece firmly against the fence throughout the feed.

Direction of grain Avoid feeding workpiece into the Jointer against the grain as shown in Fig.13. The result will be chipped and splintered edges. Fe

CHANGING PLANER BLADES 1. a Removing blades 1 Remove the screw of the chip cover. cover. on the outfeed side Then open the chip Fig. 1 Loosen t

0 Lock the drum at the position shown in Fig. 17 and loosen the hex bolts with the When removina the blade from the Auto-Planer, lock the dru

.On the Auto-Planer, press down on both ends of the blades with wooden levelers. *On the Jointer, set the leveler on the outfeed table

VARIOUS ADJUSTMENTS 1. Adjusting infeed/outfeed rollers (Auto-planer) NOTE : The planer infeed and outfeed rollers are factory adjusted. If you n

MAINTENANCE CAUTION : Always be sure that the tool is switched off and unplugged before attempting to perform inspection and maintenance. Replacing c

.Take out the worn brush, insert the new one and secure the brush holder cap. Fig. 31 Cleaning Always brush off dirt, chips and foreign matt

Sharpening planer blades (In case of blade width 155 mm (6-1/8”)) 1. Remove the two wing nuts on the holder. 2. Set the blade A and blade

BEFORE CONNECTING YOUR TOOL TO A POWER SOURCE Be sure you have read all GENERAL POWER TOOL SAFETY RULES GENERAL SAFETY PRECAUTIONS (For All Tools)

ACCESSORIES CAUTION : These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any

Dressing Stone 180-1200 (Part No. 741801-4) Key (Part No. 411447-7) Leveler (Part No. 41 1908-71 Wrench (Part No. 781202-4) 21

Seo -19-'84 US 320 mm (12-1/2") Model 2030N PLANER-JOINTER 22

23

Note: The switch and other part configurations may differ from country to country. 24

MODEL 2030N AiD DESCRIPTION Sep 19-84 US AtD DESCRIPTION MACHINE ~ 1 2 3 4 5 6 7 8 9 10 I1 16 17 IS 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 3

MODEL 2030N Sep.-19-84 US 'itM $tD DESCRIPTION ';,'d" $ZD DESCRIPTION MACHINE ~ 148 149 150 151 152 153 154 155 156 157 158 159 16

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -. . -. . . . . . . . MAKITA LIMITED ONE YEAR WARRANTY

16. 17. 18. 19. 20. 21. 22. 23. REDUCE THE RISK OF UNINTENTIONAL STARTING. Make sure switch is in off position before plugging in. USE RECOMMENDED

GROUNDING INSTRUCTIONS ALL GROUNDED, CORD-CONNECTED TOOLS: In the event of a malfunction or breakdown, grounding provides a path of least resistance

ADDITIONAL SAFETY RULES 1. 2. 3. 4. 5. 6. 7. 8. 9. IO. 11. 12. 13. 14. 15. 16. Don't use the tool in presence of flammable liquids or gases. H

ADDITIONAL SAFETY RULES FOR JOINTER 1. Maintain the proper relationships of infeed and outfeed table surfaces and cut- terhead blade path. 2. Do not

HOW TO USE AUTO-PLANER 1. Adjusting depth of cut The maximum depth of cut changes in terms of the cutting speed and the width of the workpie

3. Switchover of cutting speed Turn the speed change lever to the right for high speed, and to the left for low speed. CAUTION. Change speeds

JOINTER 1. Cutting depth Set the depth of cut with the depth adjustment knob while watching the graduation on the scale plate. Fig. 6 2. Fence