Makita EM2650LH Instruction Manual

EM2650UHEM2651UHEM2650UHN EM2650LHNEM2650LHEM2651LHPetrol BrushcutterEM2650UHEM2650UHNEM2651UHEM2650LHEM2650LHNEM2651LHINSTRUCTION MANUALImportant:Rea

10CAUTION: Before doing any work on the Petrol Brushcutter, always stop the engine and pull the spark plug connector off the spark plug. Always wear

11To meet the applicable safety provisions, only the tool/ protector combinations as indicated in the table must be used.Be sure to use genuine MAKIT

12Turn the machine upside down, and you can replace the cutter blade or nylon cutting head easily.– Insert the hex wrench through the hole in the gea

13Inspection and rell of engine oil– Perform the following procedure, with the engine cooled down.– Set the engine level, remove oil cap (Fig. 1),

14REFUELINGHandling of fuelIt is necessary to handle fuel with utmost care. Fuel may contain substances similar to solvents. Refueling must be perform

15CORRECT HANDLING OF MACHINEAttachment of shoulder strap– Adjust the strap length so that the cutter blade will be kept parallel with the ground.For

163) Primer pump Continue to push the primer pump until fuel enters into the primer pump. (In general, fuel enters into the primer pump by 7 to 1

17CAUTION: The cutting tools mentioned below must only be resharpened by an authorized facility. Manual resharpening will result in imbalances of th

18CoverLatchesPressPress80 mm (3 - 1/8”) SpoolFor left hand rotationSpool100 mm (3 - 15/16”)NotchesEyeletsReplacing the nylon cord– First, stop the e

19CAUTION: Before doing any work on the Petrol Brushcutter, always stop the engine and pull the plug cap off the spark plug (see “checking the spark

2Thank you very much for purchasing the MAKITA Petrol Brushcutter. We are pleased to recommend to you the MAKITA Petrol Brushcutter which is the resul

20CLEANING OF AIR CLEANERDANGER: INFLAMMABLES STRICTLY PROHIBITEDInterval of Cleaning and Inspection: Daily (every 10 operating hours)– Turn the chok

21CLEANING OF FUEL FILTERWARNING: INFLAMMABLES STRICTLY PROHIBITEDInterval of Cleaning and Inspection: Monthly (every 50 operating hours)Suction head

22WARNING: When draining the fuel, be sure to stop the engine and conrm that the engine cools down. Just after stopping the engine, it may still hot

23*1 Perform initial replacement after 20h operation.*2 For the 200 operating hour inspection, request Authorized Service Agent or a machine shop.

24TROUBLESHOOTINGBefore making a request for repairs, check a trouble for yourself. If any abnormality is found, control your machine according to the

25

26

27

Makita CorporationAnjo, Aichi, Japan884951F229 www.makita.comALA

315 MetersDiagrammatic gureSAFETY INSTRUCTIONSGeneral Instructions– Read this instruction manual to become familiar with handling of the equipment.

4• Resting• Transport• Refuelling• Maintenance• Tool replacement3 metersStart the brushcutter only in accordance with the instructions.– Do not use a

5Caution:KickbackDiagrammatic gureDiagrammatic gureMethod of operation– Only use in good light and visibility. During the winter season beware of s

6Never straighten or weld damaged cutting tools.– Pay attention to the environment. Avoid unnecessary throttle operation for less pollution and noise

7TECHNICAL DATAModel EM2650UH EM2650UHN EM2650LH EM2650LHNHandle type Bike handle Loop handleDimensions: length x width x height (without cutting tool

8TECHNICAL DATAModel EM2651UH EM2651LHHandle type Bike handle Loop handleDimensions: length x width x height (without cutting tool) mm 1,765 x 620 x

9DESIGNATION OF PARTS2019①③⑥⑰②⑱GB DESIGNATION OF PARTS1 Fuel tank2 Rewind starter3 Air cleaner4 I-O switch (on/off)5 Spark plug6 Exhaust mufer7 Clutc