Makita BTL061RF Datasheet download pdf (Page 8)

Installing or removing driver bit (Fig. 5)

Use only the driver bit or socket bit shown in the figure.

Do not use any other driver bit or socket bit.

To install the bit, pull the sleeve in the direction of the

arrow and insert the bit into the sleeve as far as it will go.

Then release the sleeve to secure the bit. (Fig. 6)

For tool without sleeve to retain the bit

(Fig. 7)

Use only the driver bit or socket bit shown in the figure.

Do not use any other driver bit or socket bit.

Use insert bits shown in the figure. To install the bit, just

insert it into the spindle. (Fig. 8)

NOTE:

• If the bit is not inserted deep enough into the sleeve,

the sleeve will not return to its original position and the

bit will not be secured. In this case, try re-inserting the

bit according to the instructions above.

Hook (Accessory)

CAUTION:

• When installing the hook, tighten the screw firmly.

Failure to do so may cause the breakage of the tool or

personal injury. (Fig. 9)

The hook is convenient for temporarily hanging the tool.

This can be installed on either side of the tool.

To install the hook, insert it into a groove in the tool

housing on either side and then secure it with a screw.

To remove, loosen the screw and then take it out.

Adjusting the angle head

The angle head can be adjusted 360° (8 positions in 45-

degree increments). To adjust it, loosen the hex bolt and

remove the angle head. Adjust the angle head to the

desired position and reinstall it so that the teeth on the

housing will match up with the grooves in the angle head.

Then tighten the hex bolt to secure the angle head.

(Fig. 10 & 11)

Straight head and ratchet head

(Accessory)

Straight heads and ratchet heads are available as

optional accessories for various applications on the job.

(Fig. 12 & 13)

OPERATION (Fig. 14 & 15)

The proper fastening torque may differ depending upon

the kind or size of the screw/bolt, the material of the

workpiece to be fastened, etc. Before starting your job,

always perform a test operation to determine the proper

fastening time for your screw. (Fig. 16)

NOTE:

• Use the proper bit for the head of the screw/bolt

OPERATION that you wish to use.

• Hold the tool pointed straight at the screw.

• If the tool is operated continuously until the battery

cartridge has discharged, allow the tool to rest for

15 minutes before proceeding with a fresh battery.

The fastening torque is affected by a wide variety of

factors including the following. After fastening, always

check the torque with a torque wrench.

1. When the battery cartridge is discharged almost

completely, voltage will drop and the fastening torque

will be reduced.

2. Driver bit or socket bit

Failure to use the correct size driver bit or socket bit

will cause a reduction in the fastening torque.

3. Bolt

• Even though the torque coefficient and the class of

bolt are the same, the proper fastening torque will

differ according to the diameter of bolt.

• Even though the diameters of bolts are the same,

the proper fastening torque will differ according to

the torque coefficient, the class of bolt and the bolt

length.

4. The manner of holding the tool or the material of

driving position to be fastened will affect the torque.

5. Operating the tool at low speed will cause a reduction

in the fastening torque.

MAINTENANCE

CAUTION:

• Always be sure that the tool is switched off and the

battery cartridge is removed before attempting to

perform inspection or maintenance.

To maintain product SAFETY and RELIABILITY, repairs,

any other maintenance or adjustment should be

performed by Makita Authorized Service Centers, always

using Makita replacement parts.

ACCESSORIES

CAUTION:

• These accessories or attachments are recommended

for use with your Makita tool specified in this manual.

The use of any other accessories or attachments might

present a risk of injury to persons. Only use accessory

or attachment for its stated purpose.

If you need any assistance for more details regarding

these accessories, ask your local Makita Service Center.

• Phillips bit

• Bit piece

• Straight head

• Ratchet head

• Socket

• Socket adapter

• Various type of Makita genuine batteries and chargers

1 2 3 4 5 6 7 8 9 10 11 12 13 ... 27 28

Comments to this Manuals

No comments

Makita BTL061RF Datasheet Page 8

Comments to this Manuals

Related products and manuals for Cordless combi drills Makita BTL061RF