Makita BDF452 User Manual download pdf (Page 8)

Use a cutting lubricant when drilling metals. The

exceptions are iron and brass which should be drilled dry.

CAUTION:

• Pressing excessively on the tool will not speed up the

drilling. In fact, this excessive pressure will only serve

to damage the tip of your bit, decrease the tool

performance and shorten the service life of the tool.

• There is a tremendous force exerted on the tool/bit at

the time of hole break through. Hold the tool firmly and

exert care when the bit begins to break through the

workpiece.

• A stuck bit can be removed simply by setting the

reversing switch to reverse rotation in order to back

out. However, the tool may back out abruptly if you do

not hold it firmly.

• Always secure small workpieces in a vise or similar

hold-down device.

• If the tool is operated continuously until the battery

cartridge has discharged, allow the tool to rest for 15

minutes before proceeding with a fresh battery.

MAINTENANCE

CAUTION:

• Always be sure that the tool is switched off and the

battery cartridge is removed before attempting to

perform inspection or maintenance.

Replacing carbon brushes (Fig. 11)

Replace when they wear down to the limit mark. Keep the

carbon brushes clean and free to slip in the holders.

Both carbon brushes should be replaced at the same

time. Use only identical carbon brushes.

Use a screwdriver to remove two screws then remove the

rear cover. (Fig. 12)

Raise the arm part of the spring and then place it in the

recessed part of the housing with a slotted bit screwdriver

of slender shaft or the like. (Fig. 13)

Use pliers to remove the carbon brush caps of the carbon

brushes. Take out the worn carbon brushes, insert the

new ones and replace the carbon brush caps in reverse.

(Fig. 14)

Make sure that the carbon brush caps have fit into the

holes in brush holders securely. (Fig. 15)

Reinstall the rear cover and tighten two screws securely.

To maintain product SAFETY and RELIABILITY, repairs,

any other maintenance or adjustment should be

performed by Makita Authorized Service Centers, always

using Makita replacement parts.

ACCESSORIES

CAUTION:

• These accessories or attachments are recommended

for use with your Makita tool specified in this manual.

The use of any other accessories or attachments might

present a risk of injury to persons. Only use accessory

or attachment for its stated purpose.

If you need any assistance for more details regarding

these accessories, ask your local Makita Service Center.

• Drill bits

• Screw bits

• Bit holder

•Hook

• Various type of Makita genuine batteries and chargers

• Automatic refreshing adapter

• Plastic carrying case

For Model BDF442

For European countries only

Noise and Vibration

ENG003-2

The typical A-weighted sound pressure level is 71 dB (A).

Uncertainty is 3 dB (A).

The noise level under working may exceed 85 dB (A).

Wear ear protection.

The typical weighted root mean square acceleration value

is not more than 2.5 m/s

These values have been obtained according to EN60745.

For Model BDF452

For European countries only

Noise and Vibration

ENG001-2

The typical A-weighted sound pressure level is 70 dB (A).

The noise level under working may exceed 85 dB (A).

Wear ear protection.

The typical weighted root mean square acceleration value

is not more than 2.5 m/s

These values have been obtained according to EN60745.

EC-DECLARATION OF CONFORMITY

ENH102-6

Model; BDF442, BDF452

We declare under our sole responsibility that this product

is in compliance with the following standards of

standardized documents;

EN60745, EN55014 in accordance with Council

Directives, 2004/108/EC, 98/37/EC.

CE2006

Tomoyasu Kato

Director

Responsible Manufacturer:

Makita Corporation

3-11-8, Sumiyoshi-cho, Anjo, Aichi, JAPAN

Authorized Representative in Europe:

Makita International Europe Ltd.

Michigan Drive, Tongwell, Milton Keynes, Bucks MK15

8JD, ENGLAND

1 2 3 4 5 6 7 8 9 10 11 12 13 ... 27 28

Comments to this Manuals

No comments

Makita BDF452 User Manual Page 8

Comments to this Manuals

Related products and manuals for Tools Makita BDF452