Makita DPC 6400, DPC 6401, DPC 7300, DPC 7301 Service Manual Page 27
- Page / 86
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
27
Troubleshooting
Malfunction System Observation Cause
Cutting disc does not
start turning Clutch Engine runs Damage to clutch
Engine does not start or Ignition system Ignition spark Malfunction in fuel supply system, com-
only with difficulty pression system, mechanical malfunction.
No ignition spark Switch on STOP, fault or short-circuit in the
wiring, plug cap or spark plug defective.
Fuel supply Fuel tank is filled Choke in wrong position, carburetor defective,
suction head dirty, fuel line bent or interrupted.
Compression Inside Cylinder base packing ring defective, radial
system shaft packings defective, cylinder or piston rings
defective
Outside Spark plug does not seal.
Mechanical Starter does not engage Spring in starter broken, broken parts
malfunction inside the engine.
Warm start difficulties Carburetor Fuel tank is filled Wrong carburetor adjustment.
Ignition spark
Engine starts, but Fuel supply Fuel tank is filled Wrong idling adjustment, suction head or
dies immediately carburetor dirty.
Tank venting defective, fuel line interrupted,
cable defective, STOP switch defective. Starting
valve dirty.
Insufficient power Several systems Engine is idling Air filter dirty, wrong carburetor adjustment,
may be involved muffler clogged, exhaust channel in cylinder
simultaneously clogged, spark arrester screen clogged.
Guarantee
MAKITA guarantees the highest quality and will therefore reimburse all costs for repair by replacement of damaged parts resulting from
material or production faults occurring within the guarantee period after purchase. Please note that in some countries particular
guarantee conditions may exist. If you have any questions, please contact your salesman, who is responsible for the guarantee of the
product.
Please note that we cannot accept any responsibility for damage caused by:
• Disregard of the instruction manual.
• Non-performance of the required maintenance and cleaning.
• Incorrect carburetor adjustment.
• Normal wear and tear.
• Obvious overloading due to permanent exceeding of the upper performance limits.
• The use of other than original MAKITA cutting discs.
• Use of force, improper use, misuse or accidents.
• Damage from overheating due to dirt on the fan housing.
• Work on the Power Cut by unskilled persons or inappropriate repairs.
• Use of unsuitable spare parts or parts which are not original MAKITA parts, insofar as they have caused the damage.
• Use of unsuitable or old oil.
• Damage related to conditions arising from lease or rent contracts.
Cleaning, servicing and adjustment work is not covered by the guarantee. All repairs covered by the guarantee must be performed by
a MAKITA service centre.
- (page 30 - 57) 1
- WARNING! 2
- Delivery inventory 3
- SAFETY PRECAUTIONS 4
- Fuels / Refuelling 5
- Putting into operation 5
- Cutoff discs 6
- (16 feet) 6
- Kickback and lock-in 7
- Cutting metals 8
- Cutting masonry and concrete 8
- Transport and storage 9
- Maintenance 10
- First aid 10
- Denomination of components 11
- Technical data 11
- PUTTING INTO OPERATION 12
- Caution: 13
- Tightening the V-belt / 13
- Checking V-belt tension 13
- IMPORTANT 13
- Refuelling 14
- IMPORTANT: 14
- Starting the engine 14
- Fuel storage 14
- AVOID SKIN AND EYE CONTACT 14
- CAUTION: 15
- Cold-starting 15
- Warm-starting 15
- Stopping the engine 16
- Working in winter 16
- Adjusting 17
- MAINTENANCE 18
- Cleaning the protection hood 19
- Replacing the spark plug 20
- Paper cartridge 20
- Checking the ignition spark 21
- CAUTION! 21
- Replacing the suction head 21
- Replacing the starter cable 21
- Replacing the return spring 22
- Cutting attachment in 23
- SPECIAL ACCESSORIES 25
- Maintenance and repair 26
- Spare parts 26
- Troubleshooting 27
- DPC 6400, 6401 28
- DPC 7300, 7301 28
- ATTENTION! 30
- Symboles 31
- Etendue de la fourniture 31
- INSTRUCTIONS DE SÉCURITÉ 32
- Mise en route 33
- Disques à découper 34
- (16 pieds) 34
- Rebond (kickback) et freinage 35
- Découper les métaux 36
- Transport et stockage 37
- Premier secours 38
- Désignation des pièces 39
- Caractéristiques techniques 39
- MISE EN ROUTE 40
- Remplissage des réservoirs 42
- Démarrer le moteur 42
- ATTENTION: 43
- Démarrage à froid 43
- Démarrage à chaud 43
- Arrêter le moteur 44
- Marche hivernale 44
- Réglage du carburateur 45
- TRAVAUX DE MAINTENANCE 46
- Remplacement du 50
- ACCESSOIRES OPTIONNELS 53
- Maintenance et réparations 54
- Pièces de rechange 54
- Garantie 55
- Recherche de pannes 55
- Agradecemos su confianza 58
- Extensión del suministro 59
- Símbolos 59
- RECOMENDACIONES DE SEGURIDAD 60
- Puesta en marcha 61
- Muelas de tronzar 62
- (16 pies) 62
- Separar metales 64
- Transporte y almacenamiento 65
- SERVICIO 66
- Datos técnicos 67
- PUESTA EN MARCHA 68
- Cargar combustible 70
- ATENCION: 70
- Arrancar el motor 70
- Arranque en frío 71
- Arranque en caliente: 71
- Parar el motor 72
- Aplicación en invierno 72
- Ajustar el carburador 73
- Cambiar la bujía 76
- ATENCIÓN: 76
- Cartucho de papel 76
- ¡ATENCIÓN! 77
- Recambio del muelle 78
- Cambio de posición del 79
- PRECAUCIÓN: 80
- ACCESORIOS ESPECIALES 81
- Mantenimiento y reparaciones 82
- Piezas de repuesto 82
- Localización de averías 83
- Makita U.S.A., Inc 86
- Makita Canada Inc 86
Related products and manuals for Power tools Makita DPC 6400, DPC 6401, DPC 7300, DPC 7301
Power tools Makita 6831D Instruction Manual
(15 pages)
(15 pages)
Power tools Makita UC120D Instruction Manual
(12 pages)
(12 pages)
Power tools Makita PW5001C Specifications
(16 pages)
(16 pages)
Power tools Makita UH200D Instruction Manual
(96 pages)
(96 pages)
(88 pages)
Power tools Makita BBO180 Instruction Manual
(12 pages)
(12 pages)
Power tools Makita 6834 Instruction Manual
(16 pages)
(16 pages)
Power tools Makita HM1400K User Manual
(28 pages)
(28 pages)
Power tools Makita BHP444 Instruction Manual
(12 pages)
(12 pages)
Power tools Makita 6911HD Instruction Manual
(16 pages)
(16 pages)
Power tools Makita JS1670 Instruction Manual
(10 pages)
(10 pages)
Power tools Makita FS2700 User Manual
(36 pages)
(36 pages)
Power tools Makita 3709 Instruction Manual
(12 pages)
(12 pages)
Power tools Makita FS2701 Instruction Manual
(20 pages)
(20 pages)
Power tools Makita BHR241 User Manual
(52 pages)
(52 pages)
© 2020, manymanuals.com. All rights reserved. | 2.484 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals