Makita LS1013 User Manual Page 10
- Page / 72
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
10
Return the blade guard and center cover to its original
position. Then tighten the hex bolt clockwise to secure
the center cover. Release the handle from the raised
position by pulling the stopper pin. Lower the handle to
make sure that the blade guard moves properly. Make
sure shaft lock has released spindle before making cut.
Dust bag
The use of the dust bag makes cutting operations clean
and dust collection easy. To attach the dust bag, fit it onto
the dust nozzle.
When the dust bag is about half full, remove the dust bag
from the tool and pull the fastener out. Empty the dust
bag of its contents, tapping it lightly so as to remove par-
ticles adhering to the insides which might hamper further
collection.
NOTE:
If you connect a vacuum cleaner to your saw, more
efficient and cleaner operations can be performed.
Securing workpiece
WARNING:
• It is extremely important to always secure the
workpiece properly and tightly with the vise. Failure
to do so can cause the tool to be damaged and/or
the workpiece to be destroyed. PERSONAL
INJURY MAY ALSO RESULT. Also, after a cutting
operation, DO NOT raise the blade until the blade
has come to a complete stop.
CAUTION:
• When cutting long workpieces, use supports that
are as high as the top surface level of the turn base.
Do not rely solely on the vertical vise and/or
horizontal vise to secure the workpiece.
Thin material tends to sag. Support workpiece over
its entire length to avoid blade pinch and possible
KICKBACK.
Sub-fence
This tool is equipped with the sub-fence which should
ordinarily be positioned as shown in the figure.
However, when performing left bevel cuts, set it to the left
position as shown in the figure.
1. Blade case
2. Arrow
3. Saw blade
4. Arrow
1. Hex bolt
2. Outer flange
3. Saw blade
4. Inner flange
5. Spindle
1. Center cover
2. Hex bolt
3. Socket wrench
4. Blade guard
1. Dust nozzle
2. Dust bag
3. Fastener
2 1 4 3
001534
12 4
3
5
001786
3
1
2
4
001532
3
1
2
001536
1. Support
2. Turn base
1. Sub-fence
1
2
001549
1
001545
- Slide Compound Saw 1
- Scie Multi Coupe 1
- Sierra de Inglete Telescópica 1
- SPECIFICATIONS 2
- Save it for future reference 2
- GENERAL SAFETY PRECAUTIONS 2
- ADDITIONAL SAFETY RULES 3
- SAVE THESE INSTRUCTIONS 4
- FOR THE LASER 5
- INSTALLATION 5
- FUNCTIONAL DESCRIPTION 5
- Positioning kerf board 6
- Stopper arm 7
- Adjusting the miter angle 7
- Adjusting the bevel angle 7
- Switch action 7
- Electric brake 8
- Lighting up the lamps 8
- Laser beam action 8
- ASSEMBLY 9
- Dust bag 10
- Securing workpiece 10
- Sub-fence 10
- Vertical vise 11
- OPERATION 12
- Left and Right 0˚ - 45˚ 13
- Right 52˚ 13
- Miter angle Bevel angle 13
- Table (A) 14
- Table (B) 14
- Compound Miter Saw 16
- Table (C) 18
- MAINTENANCE 19
- Replacing fluorescent tube 22
- Replacing carbon brushes 22
- After use 22
- ACCESSORIES 23
- (Pour TOUS LES OUTILS) 24
- RÈGLES DE SÉCURITÉ 26
- SUPPLEMENTAIRES 26
- CONSERVEZ CE MODE 27
- D’EMPLOI 27
- CONSIGNES DE SÉCURITÉ 27
- ADDITIONNELLES POUR LE 27
- DESCRIPTION DU 28
- FONCTIONNEMENT 28
- Bras de blocage 29
- Interrupteur 30
- Frein électrique 31
- Allumage de la lampe 31
- Action du faisceau laser 31
- ASSEMBLAGE 32
- Sac à poussières 33
- Immobilisation de la pièce 33
- Garde auxiliaire 34
- Garde auxiliaire de droite 34
- (accessoire en option) 34
- Étau vertical 34
- UTILISATION 35
- (1) (2) (3) (4) 37
- Tableau (A) 38
- Tableau (B) 38
- Scie à coupe d’onglet mixte 39
- Tableau ( 41
- ENTRETIEN 42
- ACCESSOIRES 46
- EN0006-1 47
- (PARA TODAS LAS HERRAMIENTAS) 48
- NORMAS DE SEGURIDAD 50
- ADICIONALES 50
- GUARDE ESTAS 51
- INSTRUCCIONES 51
- ADICIONALES PARA EL LÁSER 51
- INSTALACIÓN 52
- DESCRIPCIÓN DEL 52
- FUNCIONAMIENTO 52
- Brazo de retención 53
- Ajuste del ángulo inglete 54
- Ajuste del ángulo bisel 54
- Accionamiento del interruptor 54
- Freno eléctrico 55
- Encendido de las linternas 55
- Accionamiento del rayo láser 55
- Bolsa recolectora de polvo 57
- Aseguramiento de la pieza 57
- Guía auxiliar 58
- Prensa vertical 58
- OPERACIÓN 59
- Tabla (A) 62
- Tabla (B) 62
- Sierra de Inglete 63
- Tabla (C) 65
- MANTENIMIENTO 66
- ACCESORIOS 70
- ADVERTENCIA 72
Related products and manuals for Power saws Makita LS1013
Power saws Makita 5740NB User Manual
(16 pages)
(16 pages)
Power saws Makita LF1000 User Manual
(36 pages)
(36 pages)
Power saws Makita LS0714L User Manual
(32 pages)
(32 pages)
Power saws Makita LH1040F User Manual
(60 pages)
(60 pages)
Power saws Makita LS1013L User Manual
(24 pages)
(24 pages)
Power saws Makita LS1040F User Manual
(44 pages)
(44 pages)
Power saws Makita LS1216FL User Manual
(32 pages)
(32 pages)
Power saws Makita 4114S User Manual
(12 pages)
(12 pages)
Power saws Makita 4131 User Manual
(16 pages)
(16 pages)
Power saws Makita 2704 User Manual
(20 pages)
(20 pages)
Power saws Makita 5143R User Manual
(28 pages)
(28 pages)
Power saws Makita 4329K User Manual
(32 pages)
(32 pages)
Power saws Makita 5604RK User Manual
(16 pages)
(16 pages)
Power saws Makita 3706 User Manual
(24 pages)
(24 pages)
Power saws Makita 5704RK User Manual
(28 pages)
(28 pages)
Power saws Makita BJV180RFE User Manual
(16 pages)
(16 pages)
© 2020, manymanuals.com. All rights reserved. | 0.428 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals