Instruction Manual Original Instruction Manual EK7300 EK7301 Important: Read this instruction manual carefully before putting the Power Cut into opera
Maintenance - Before performing maintenance work switch off the Power Cut (27) and pull out the plug cap. - Always check the Power Cut before using
Technical data EK7300 EK7301 Displacement cm3 73 Bore mm 50 Stroke mm 37 Max. power kW 3.8 Max. torque Nm 4.3 Idling speed 1/min 2.500 Clu
Denomination of components 3 4 5 6 7 2 1 14 13 12 11 10 24 23 22 Identifi cation plate (12)EK7301 2011 123456 Indicate when ordering spare
PUTTING INTO OPERATION CAUTION: Always turn off the engine and pull off the spark plug cap before doing any work on the Power Cut! Always w
Tightening the V-belt / Checking V-belt tension IMPORTANT: Exact V-belt tension is essential for maximum cutting per-formance with minimum fuel consum
MAKITA high-performance two-stroke engine oil (50:1) is available in the following sizes to suit your individual require-ments: 100 ml order
Starting the engine if necessary This model is fi tted with a semiautomatic decompression valve (1) to make starting easier. Press the rubber cover unt
6 5 8 9 Cold start (Choke) Warm start Engine off Cold starting: Grasp front handle fi rmly with one hand and press the Power Cut against the ground. P
For correct adjustment of the idling speed the following steps must be carried out: Start the engine and run it until it is warm (about 3
MAINTENANCE CAUTION: Before doing any work on the Power Cut turn off the engine, remove the cutting disc, pull the plug cap off the spark plug and
Thank you for purchasing a MAKITA product! Congratulations on choosing a MAKITA Power Cut cutoff saw! We are condent that you will be satised
Cleaning the protection hood Over time, the inside of the protective hood can become caked with material residue (especially from wet cutting),
CAUTION: Turn off the engine before cleaning the air filter! Never clean out the air filter with compressed air! Do not clean the pre-filter and inner fi
Replacing the spark plug CAUTION: Do not touch the spark plug or plug cap if the engine is running (high voltage). Switch off the engine befor
Replacing the starter cable 181415Remove four screws (14). Remove starter housing (15). Insert a small screwdriver through the cooling slits on the ba
Replacing the return spring Remove the starter housing (see “Replacing the starter cable”). Take the air guide off the starter housing (se
Cutting attachment in central / side position NOTE: The Power Cut is delivered with the cutting attachment mounted in the middle position (1). For cut
Press the cutting attachment (13) onto the drive arm in the side position. Guide the V-belt (14) over the V-belt pulley (15). 13 1415 Put
SPECIAL ACCESSORIES Diamond cutting discs (1) MAKITA diamond cutting discs meet the highest demands in working safety, ease of operation
Instructions for periodic maintenance To ensure long life, prevent damage and ensure the full functioning of the safety features the following mainten
Guarantee MAKITA guarantees the highest quality and will therefore reimburse all costs for repair by replacement of damaged parts resulting from mater
Delivery inventory 654321 1. Power Cut 2. Cutting disc (not in the general scope of delivery. Country-specific) 3. Adapter ring 20/25.4 (not in the
Extract from the spare parts list EK7300 Use only original MAKITA parts. For repairs and EK7301replacement of other parts, see your MAKITA servi
Extract from the spare parts list EK7300 Use only original MAKITA parts. For repairs and EK7301replacement of other parts, see your MAKITA service cen
To find your local distributor, please visit www.makita-outdoor.com MAKITA Corporation Specifications subject to change without notice 3-11-8 Su
SAFETY PRECAUTIONS Intended use Power Cut Use the Power Cut cutoff saw outdoors only, for trimming and cutting suitable materials, using cutting discs
- Always wear safety shoes or boots (G) with steel toes, non-skid soles, and leg protectors when working with the Power Cut. Safety shoes eq
Cutoff discs - The protection hood must always be on! Change discs only with the engine off! - There are two basic types of cutoff discs: - For meta
Kickback and lock-in - When working with the Power Cut there is a danger of kickback and lock-in. - Kickback occurs when the top of the cutting dis
When using synthetic resin cutting discs, always ob-serve the following: CAUTION: - Synthetic resin cutting discs can absorb moisture.
In wet cutting, the disc is wetted at an equal rate on both sides by a trickle of water. MAKITA offers the right accessories for all wet cutting appli
Comments to this Manuals