GBSlide Compound Saw Instruction ManualFScie radiale Manuel d’instructionsDVerbund-Tischkreissäge BetriebsanleitungISega composita a slitta Istruzioni
10Symbols The followings show the symbols used for the tool. Be sure that you understand their meaning before use. Symboles Nous donnons ci-dessous le
11❏ To avoid injury from flying debris, keep holding the saw head down, after making cuts, until theblade has come to a complete stop.❏ Pour éviter le
12❏ For your safety, remove chips, small pieces, etc. from the table top before operation.❏ Pour votre sécurité, retirez les copeaux et autres petites
13ENGLISH Explanation of general view 1 Stopper pin 2Bolt 3 Adjusting bolt 4 Blade guard A5 Thumb screw 6 Kerf board 7 Saw blade 8 Blade teeth 9 Left
14• Due to our continuing program of research and devel-opment, the specifications herein are subject to changewithout notice. • Note: Specifications
15INSTALLATION Bench mounting When the tool is shipped, the handle is locked in the low-ered position by the stopper pin. Release the stopper pinby l
16Adjusting the bevel angle (Fig. 12 & 13)To adjust the bevel angle, loosen the lever at the rear ofthe tool counterclockwise. Push the handle to
17Aligning the laser line (Fig. 20)Laser line can be shifted to either the left or right side ofthe blade according to the applications of cutting. Re
18CAUTION: • The workpiece must be secured firmly against the turnbase and guide fence with the vise during all opera-tions. Horizontal vise (optional
194. Bevel cut (Fig. 38)Loosen the lever and tilt the saw blade to set the bevelangle (Refer to the previously covered “Adjusting thebevel angle”). Be
21234567811312786910564485321
20MAINTENANCE CAUTION: • Always be sure that the tool is switched off andunplugged before attempting to perform inspection ormaintenance. WARNING: • A
21For both adjustments, do as follows. 1. Make sure that the tool is unplugged. 2. Draw the cutting line on the workpiece and place iton the turn tabl
54NEDERLANDS Verklaring van algemene gegevens 1 Aanslagpen 2Bout 3 Stelbout 4 Beschermkap A5 Vleugelschroef 6 Zaagsnedeplaat 7 Zaagblad 8 Zaagbladtand
55Toerental onbelast (min–1)...
56Het gevaar van blootstelling hangt af van hoevaak u dit soort werk uitvoert. Om blootstellingaan deze chemicaliën tot een minimum te beper-ken, die
57Handhaven van de maximale zaagcapaciteit (Fig. 8 en 9)Deze zaag is in de fabriek ingesteld voor het leveren vanmaximale zaagcapaciteit met een 190 m
58Aanzetten van de lampen (Fig. 17)Voor de modellen LS0714F, LS0714FL LET OP: • De lamp is niet waterdicht. Was de lamp niet in wateren gebruik hem ni
59Breng de beschermkap en de middenkap terug naar hunoorspronkelijke positie. Draai daarna de zeskante boutnaar rechts vast om de middenkap vast te ze
60Houders en houdermontage (los verkrijgbare accessoires) (Fig. 34 en 35)U kunt de houders en de houdermontage aan beide zij-den van het gereedschap a
61• Wanneer u het handvat omlaag drukt, dient u druk uitte oefenen evenwijdig met het zaagblad. Indien de druktijdens het zagen niet evenwijdig is met
391011 1213 1415 16141213272628212125231924222117191118201615
62Afstellen van de zaaghoek Dit gereedschap werd in de fabriek nauwkeurig afgestelden uitgelijnd, maar door ruwe behandeling kan de uitlij-ning ervan
635. Steek de stekker in het stopcontact en zet de laser-schakelaar aan. 6. Stel de positie van de laserlijn als volgt af. De positie van de laserlijn
417 1819 2021 2223 2438394035413437353613233AB15312930
525 2627 2829 3031 328986905025515212495348 11898686878847454640 39397742434441
6m33 343536 3757525952585251 5255545356
738 394041 4243 4416766512563656550 mm 60 mm(2" 2-3/8")27 mm (1-1/16")85 mm(3-3/8")70 mm(2-3/4")85 mm(3-3/8")70
845 4647 4849 5051 5271232519687132518192169702422681236527273
982838480535455 5657 588081827576777875795274
Comments to this Manuals